Logic synthesizers usually have good area minimization capabilities, producing circuits of minimal area. But good delay minimization techniques are still missing in current logic synthesis technology. In [7], the RENO algorithm (which stands for REsynthesis for Network Optimization) was proposed for minimizing the area of multi-level combinational networks, and its effectiveness in designing minimal-area networks has been demonstrated. In this paper, we present improvements and extensions of the RENO algorithm for network delay minimization by using Boolean resynthesis techniques. We will discuss new algorithms for gate resynthesis which have not only reduced the processing time significantly, but also have improved the quality of minimization. Due to the generality of the gate resynthesis algorithms, we can minimize both delay and area of a network concurrently in a unified way, and network delay is reduced significantly with no or very small area penalty. Extensive experimental results and comparison with the speed_up algorithm in SIS-1.0 are presented.

Internet routers need to classify incoming packets quickly into flows in order to support features such as Internet security, virtual private networks and Quality of Service (QoS). Packet classification uses information contained in the packet header, and a predefined rule table in the routers. Packet classification of multiple fields is generally a difficult problem. Hence, researchers have proposed various algorithms. This study proposes a multi-dimensional encoding method in which parameters such as the source IP address, destination IP address, source port, destination port and protocol type are placed in a multi-dimensional space. Similar to the previously best known algorithm, i.e., bitmap intersection, multi-dimensional encoding is based on the multi-dimensional range lookup approach, in which rules are divided into several multi-dimensional collision-free rule sets. These sets are then used to form the new coding vector to replace the bit vector of the bitmap intersection algorithm. The average memory storage of this encoding is θ (LNlog N) for each dimension, where L denotes the number of collision-free rule sets, and N represents the number of rules. The multi-dimensional encoding practically requires much less memory than bitmap intersection algorithm. Additionally, the computation needed for this encoding is as simple as bitmap intersection algorithm. The low memory requirement of the proposed scheme means that it not only decreases the cost of packet classification engine, but also increases the classification performance, since memory represents the performance bottleneck in the packet classification engine implementation using a network processor.

The hybrid antenna consisted of cylindrical dielectric resonator and rectangular slot was implemented. The hybrid antenna resonated at two different frequencies. The lower resonant frequency was associated with the rectangular slot while the higher resonant frequency was associated with the cylindrical dielectric resonator. Parametric investigation was carried out using simulation software. The proposed hybrid antenna had good agreement between the simulation and measurement results. A 24% bandwidth (return loss < 10 dB) of 2.30 GHz, and a 18% bandwidth (return loss < 10 dB) of 5.46 GHz was implemented successfully for application in ISM and UNII band.

Researchers have developed several social-based routing protocols for delay tolerant networks (DTNs) over the past few years. Two main routing metrics to support social-based routing in DTNs are centrality and similarity metrics. These two metrics help packets decide how to travel through the network to achieve short delay or low drop rate. This study presents a new routing scheme called Community-Relevance based Opportunistic routing (CROP). CROP uses a different message forwarding approach in DTNs by combining community structure with a new centrality metric called community relevance. One fundamental change in this approach is that community relevance values do not represent the importance of communities themselves. Instead, they are computed for each community-community relationship individually, which means that the level of importance of one community depends on the packet's destination community. The study also compares CROP with other routing algorithms such as BubbleRap and SimBet. Simulation results show that CROP achieves an average delivery ratio improvement of at least 30% and can distribute packets more fairly within the network.

Almost stoichiometric YBa2Cu3O7-δ(110) or (103) and SrTiOx(110) films, and multilayer films consisting of them have successfully been grown epitaxially on hot SrTiO3 substrates by 90off-axis rf magnetron sputtering with facing targets. Their whole composition, compositional distribution in depth, crystallinity and surface morphology were examined by inductively coupled plasma spectroscopy, Auger electron spectroscopy, reflection high-energy electron diffraction, and scanning tunneling microscopy or atomic force microscope, respectively. When any YBa2Cu3O7-δ film was exposed to air after deposition, a Ba-rich layer was formed in a near surface region of the film. However, such a compositional distribution in depth of the film was improved by in situ deposition of a SrTiOx film on it. Moreover, the surface roughness of the YBa2Cu3O7-δ film was improved by predeposition of a SrTiOx film under it. On the basis of these results, both YBa2Cu3O7-δ/SrTiOx/YBa2Cu3O7-δ/SrTiO3(sub.) and YBa2Cu3O7-δ/SrTiOx/YBa2Cu3O7-δ/SrTiOx/SrTiO3(sub.) multilayer films with average surface roughness of 3 nm were grown reproducibly, which had uniform compositional distribution throughout the depth of the film except a near surface region of the top YBa2Cu3O7-δ layer. A new 222 structure described by Sr8Ti8O20 (Sr2Ti2O5) with a long range ordered arrangement of oxygen vacancies was formed in the SrTiOx films deposited epitaxially on YBa2Cu3O7-δ films.