In this paper, a compact ultra-wideband bandpass filter (UWB-BPF) using pseudo-interdigital stepped-impedance resonators (PIDT-SIRs) is designed and implemented on a commercial printed circuit board (PCB) of RT/Duroid 5880 substrate. The first two resonant modes of the SIR are coupled together and they are applied to create a wide passband. The proposed filter at center frequency f0 of 7.1 GHz has very good measured characteristics including the bandwidth of 3.68-10.46 GHz (3-dB fractional bandwidth of 95%), low insertion loss of -0.50.4 dB, sharp rejection due to two transmission zeros in the passband edge created by the inter-stage coupling. Experimental results of the fabricated filter show a good agreement with the predicted results.

This investigation proposes a modified equivalent circuit of single complementary split-ring resonator (CSRR) in planar transmission media and a dual-mode ring bandpass filter (BPF) that uses periodic CSRRs to suppress the spurious response. The proposed modified equivalent circuit consists of lumped elements that can be easily extracted from the measured S parameters. The proposed dual-mode ring BPF has exhibits a wide stopband characteristic owing to the bandgap resonant characteristic of CSRRs in the harmonic frequency of the dual-mode ring BPF. Good agreement with EM simulation and measurement is demonstrated.

A novel low insertion-loss and wideband microstrip bandpass filter has been designed and tested. The basic configuration of this novel dual-mode filter is a square ring resonator with direct-connected orthogonal feed lines, and dual-perturbation elements are introduced within the resonator at symmetrical location. The effects of the size of the perturbation element are studied. A new filter having wider bandwidth and transmission zeros are presented. The proposed filter responses are in good agreement with the simulations and experiments.

In this letter, the fabrication of a compact and high performance semi-lumped coplanar waveguide low-pass filter (CPW-LPF) on high resistivity silicon (HRS) substrate at millimeter wave is proposed. The design procedure and the equivalent circuit of the proposed semi-lumped CPW-LPF is discussed. The filter structure of is very simple but its performances is fairly good. This designed filter at cutoff frequency fc of 31 GHz has very good measured characteristics including the low insertion loss, sharp rejection and low group delay, due to the reduced substrate loss of HRS. Experimental results of the fabricated filter show a good agreement with the predicted results.

A novel dual mode bandpass filter (BPF) with improved spurious response is presented in this letter. To obtain low insertion loss, the coupling structure using the dual mode resonator and the feeding scheme using coplanar-waveguide (CPW) are constructed on the two sides of a dielectric substrate. A defected ground structure (DGS) is designed on the ground plane of the CPW to achieve the goal of spurious suppression of the filter. The filter has been investigated numerically and experimentally. Measured results show a good agreement with the simulated analysis.

Novel dual-band bandpass filter (BPF) with quasi-elliptic function response by using the meander coupled step-impedance resonators (SIRs) is presented. By tuning the appropriate impedance ratio (K) and physical length of SIRs, the BPF has good dual-band performance at 2.4 and 5.2 GHz with high selectivity, due to the transmission zeros appeared in two passband edges. Measured results of the proposed BPF have a good agreement with the electromagnetic (EM) simulated results.

This paper proposes a parallel coupled microstrip bandpass filter (BPF) with ring Electromagnetic Bandgap (EBG) cells on the middle layer for spurious suppression. The ring EBG cells of the middle layer add a good stopband-rejection mode to the second harmonics of the parallel coupled microstrip BPF with suppression of over -50 dB, without affecting the center frequency and insertion loss of the original designed BPF. The design of ring EBG cells is presented and verified by the experimented results.

In this paper, an inverse S-shaped slotted ground structure (S-SGS) is proposed and analyzed. The S-SGS generates dual attenuation poles that can be easily controlled by its structure parameters. The equivalent circuit of the S-SGS consists of lumped elements that can be extracted from the measured S parameters. Moreover, several S-SGS cells are applied to form a miniaturized lowpass filter (LPF), which has a smaller area and a wider stopband in comparison to previous works.