A 2-D beam scanning array antenna fed by a compact 16-way 2-D beamforming network (BFN) designed in Broadside Coupled Stripline (BCS) is addressed. The proposed 16-way 2-D BFN is formed by interconnecting two groups of 4x4 Butler Matrix (BM). Each group is composed of four compact 4x4 BMs. The critical point of the design is to propose a simple and compact 4x4 BM without crossover in BCS to achieve a better transmission coefficient of the 16-way 2-D BFN with reduced size of merely 0.8λ0×0.8λ0×0.04λ0. Moreover, the complexity of the interface connection between the 2-D BFN and the 4x4 patch array antenna is reduced by using probe feeding. The 16-way 2-D BFN is able to produce the phase shift of ±45°, and ±135° in x- and y- directions. The 2-D BFN is easily integrated under the 4x4 patch array to form a 2-D phased array capable of switching 16 beams in both elevation and azimuth directions. The area of the proposed 2-D beam scanning array antenna module has been significantly reduced to 2λ0×2λ0×0.04λ0. A prototype operating in the frequency range of 4-6GHz is fabricated and measured to validate the concept. The measurement results agree well with the simulations.

In this article, a new Beamforming Network (BFN) realized in Broadside Coupled Stripline (BCS) is proposed to feed 1×4 and 2×2 arrays antenna at 28 GHZ-Band. The new BFN is composed only of couplers and phase shifters. It doesn't require any crossover compared to the conventional Butler Matrix (BM) which requires two crossovers. The tight coupling and low loss characteristics of the BCS allow a design of a compact and wideband BFN. The new BFN produces the phase differences of (±90°) and (±45°, ±135°) respectively in x- and y-directions. Its integration with a 1×4 linear array antenna reduces the array area by 70% with an improvement of the gain performance compared with the conventional array. The integration with a 2×2 array allows the realization of a full 2-D beam scanning. The proposed concept has been verified experimentally by measuring the fabricated prototypes of the BFN, the 1-D and 2-D patch arrays antennas. The measured 11.5 dBi and 11.3 dBi maximum gains are realized in θ0 = 14° and (θ0, φ0) = (45°,345°) directions respectively for the 1-D and 2-D patch arrays. The physical area of the fabricated BFN is only (0.37λ0×0.3λ0×0.08λ0), while the 1-D array and 2-D array antennas areas without feeding transmission lines are respectively (0.5λ0×2.15λ0×0.08λ0) and (0.9λ0×0.8λ0×0.08λ0).

In this paper, we propose a radio frequency (RF) anti-aliasing filter design method considering the effect of a roll-off characteristic on a noise figure (NF) in the direct RF undersampling receiver. The proposed method is useful for broadband reception that a system bandwidth (BW) has nearly half of the sampling frequency (1/2 fs). When the system BW is extended nearly 1/2 fs, the roll-off band is out of the desired Nyquist zone and it affects NF additionally. The proposed method offers a design target regarding the roll-off characteristic not only the rejection ratio. The target is helpful as a design guide to meet the allowed NF. We design the filter based on the proposed method and it is applied to the direct RF undersampling on-board receiver for Ka-band high throughput satellite (HTS). The measured NF value of the implemented receiver almost matched the designed value. Moreover, the receiver achieved the reception bandwidth which is 90% of 1/2 fs.

We propose a spectrum regeneration and demodulation method for multiple direct RF undersampled real signals by using a new algorithm. Many methods have been proposed to regenerate the RF spectrum by using undersampling because of its simple circuit architecture. However, it is difficult to regenerate the spectrum from a real signal that has a band wider than a half of the sampling frequency, because it is difficult to include complex conjugate relation of the folded spectrum into the linear algebraic equation in this case. We propose a new spectrum regeneration method from direct undersampled real signals that uses multiple clocks and an extended algorithm considering the complex conjugate relation. Simulations are used to verify the potential of this method. The validity of the proposed method is verified by using the simulation data and the measured data. We also apply this algorithm to the demodulation system.

To reduce the complexity of direct radio frequency (RF) undersampling real-time spectrum monitoring in wireless Internet of Things (IoT) bands (920MHz, 2.4GHz, and 5 GHz bands), a design method of sampling frequencies is proposed in this paper. The Direct RF Undersampling receiver architecture enables the use of ADC with sampling clock lower frequency than receiving RF signal, but it needs RF signal identification signal processing from folded spectrums with multiple sampling clock frequencies. The proposed design method allows fewer sampling frequencies to be used than the conventional design method for continuous frequency range (D.C. to 5GHz-band). The proposed method reduced 2 sampling frequencies in wireless IoT bands case compared with the continuous range. The design result using the proposed method is verified by measurement.