RF under sampling is more suitable for Satellite receiver systems in comparison to terrestrial systems. In conventional RF under sampling the minimum sampling frequency (fs) should be atleast twice the system bandwidth; therefore for a system with a wide bandwidth, a relatively high fs is necessary. In this paper we propose a direct RF under sampling reception method that halves fs. The proposed f's is achieved by folding in band noise in half. A method of adapting f's for the reception of signals in different channels is also proposed; this ensures that the SNR is not degraded for any channel. To evaluate the proposed technique's performance and compare it to the conventional case a 3 channel, 1 GHz band test receiver and it's key device (i.e. S/H circuit) are developed. Using SNR and EVM as performance indexes, the performance of the proposed technique has been evaluated and compared to that of the conventional technique. The evaluation results show that the proposed technique can achieve the same performance as conventional RF under sampling for all 3 channels, using only half of the sampling frequency of the conventional technique.

An analog pre-distortion linearizer employing a radio frequency (RF) transistor with a self base bias control circuit is proposed. The self base bias control circuit extracts the envelope from the modulated input RF signal of the RF transistor and automatically controls its base current according to the extracted envelope. As a result, the proposed linearizer realizes positive gain deviation at high input power level. By adding a resistor between the RF transistor and the self base bias control circuit, the negative gain deviation can be derived. The design of the proposed lineaizer is described with taking the envelope frequency response of the self base bias control circuit into consideration. The fabricated linearizer achieves the adjacent channel power leakage ratio (ACLR) improvement of 8.1 dB for a 2 GHz-band, 10 W-class GaAs FET high-power amplifier (HPA) with negative gain deviation for W-CDMA base stations. It also achieves the ACLR improvement of 8.3 dB for a LDMOS HPA with positive gain deviation for the same application.

An even harmonic quadrature mixer (EH-QMIX) with a balanced configuration is proposed for a direct conversion receiver. The unit even harmonic mixer (EHMIX) used for I/Q paths consists of two anti parallel diode pairs (APDPs) and a pair of diplexers. When the second harmonic of LO (2LO) from the LO section is applied to the LO port as a spurious component, a conventional single-ended EHMIX using APDP converts the 2LO leakage from the LO section into the baseband and the d.c. offset and the self-detected LO noise arise at the baseband degrade the sensitivity. This proposed balanced EHMIX configuration can cancel out the 2LO leakage in itself. Therefore, the d.c. offset and the LO noise are significantly suppressed and the degradation of the sensitivity can be avoided. The suppression characteristic of the d.c. offset and the LO noise are verified by the simulation and the measurements. By using this balanced configuration, the fabricated EH-QMIX achieves wider frequency band characteristic than that of the single-ended EH-QMIX, and it shows 20% relative bandwidth at L-band.

An L-band low quiescent current and low distortion SiGe heterojunction bipolar transistor (HBT) driver amplifier having a self base bias control circuit is described. Since the size of this bias circuit is small and it does not need an external control circuit, it is easy to be integrated with the driver amplifier on a single chip. According to the output power level, the self base bias control circuit, which is the combination of a constant base voltage circuit and p-metal oxide semiconductor (MOS) FET current mirror with a constant current source, automatically controls the base voltage, and allows low quiescent current at low output power level and low distortion at high output power level. The simulated results show that the driver amplifier having the self base bias control circuit achieves 1 dB power compression point (P1 dB) improvement of 2.4 dB compared with the driver amplifier having a conventional constant base voltage under the same quiescent current condition. The fabricated driver amplifier with the proposed bias circuit shows high P1 dB of 15.0 dBm with low quiescent current of 15.3 mA.

This paper presents a theoretical analysis and experimental confirmation of a tunable ring resonator that can independently change its resonant frequency and bandwidth. The tunable ring resonator comprises a ring resonator, three tunable capacitors, and switches. The resonant frequency changes according to the capacitance of tunable capacitors, and the bandwidth varies by changing the state of the switches. The unique feature of the resonator is that the resonant frequency remains steady when the bandwidth is changed. The fundamental characteristics are shown based on linear circuit simulation and electromagnetic simulation results. The resonator is fabricated using GaAs FET single-pole single-throw switches. The fabricated resonator changes the resonant frequency from 1.5 GHz to 2.0 GHz and the fractional bandwidth from 5% to 30%.

In this paper, we propose a direct digital RF transmitter with a 1-bit band-pass delta-sigma modulator (BP-DSM) that uses high order image components of the 7th Nyquist zone in Manchester coding for microwave and milimeter wave application. Compared to the conventional non-return-to-zero (NRZ) coding, in which the high order image components of 1-bit BP-DSM attenuate severely in the form of sinc function, the proposed 1-bit direct digital RF transmitter in Manchester code can improve the output power and signal-to-noise ratio (SNR) of the image components at specific (4n-1)th and (4n-2)th Nyquist Zone, which is confirmed by calculating of the power spectral density. Measurements are made to compare three types of 1-bit digital-to-analog converter (DAC) signal in output power and SNR; NRZ, 50% duty return-to-zero (RZ) and Manchester coding. By using 1 Vpp/8Gbps DAC output, 1-bit signals in Manchester coding show the highest output power of -20.3dBm and SNR of 40.3dB at 7th Nyquist Zone (26GHz) in CW condition. As a result, compared to NRZ and RZ coding, at 7th Nyquist zone, the output power is improved by 8.1dB and 6dB, respectively. Meanwhile, the SNR is improved by 7.6dB and 4.9dB, respectively. In 5Mbps-QPSK condition, 1-bit signals in Manchester code show the lowest error vector magnitude (EVM) of 2.4% and the highest adjacent channel leakage ratio (ACLR) of 38.2dB with the highest output power of -18.5dBm at 7th Nyquist Zone (26GHz), respectively, compared to the NRZ and 50% duty RZ coding. The measurement and simulation results of the image component of 1-bit signals at 7th Nyquist Zone (26GHz) are consistent with the calculation results.

In this paper, we propose a novel baseband (BB) phase shifter (PS) using a fixed-gain-amplifier (FGA) matrix. The proposed BB PS consists of 5 stages of a vector synthesis type FGA matrix with in-phase/quadrature-phase (I/Q) input/output interfaces. In order to achieve low gain variation between phase shift states, 3rd to 5th stages are designed to have a phase shift of +φi and -φi (i=3,4,5). To change between +φi and -φi phase shift states, two FGAs with DC bias in-phase/out-phase switches are used. The two FGAs have the same gain, therefore ideally no gain variation can be achieved. Using this configuration, phase shift error and gain variation caused by process mismatch and temperature variation can be reduced. Fabricated 5-bit BB PS has 3-dB bandwidth of 1.05GHz, root-mean-square (rms) phase errors lower than 2.2°, rms gain variations lower than 0.42dB. Power consumption of the PS core and output buffer are 4.9mW and 14.3mW, respectively. 1-dB compression output power is -12.5dBm. The fabricated PS shows that the total phase shift error and gain variation are within the required accuracy of a 5-bit PS with no requirement of calibration.

A 0.4-5.8 GHz SiGe-MMIC quadrature modulator (Q-MOD) employing a self current controlled mixer for cognitive radio is described. The self current controlled mixer consists of a Gilbert cell mixer and a self current control circuit which is composed of both a current feedback circuit and an output buffer amplifier. The self current control circuit automatically controls the mixer current according to the output power level, and improves the linearity over wide radio frequency (RF) range. Simulation results show that the proposed Q-MOD realizes 1 dB compression point (P1 dB) improvement of more than 3.0 dB compared to the conventional Q-MOD at the frequencies of 0.4, 0.8, 1.95, 5.2 and 5.8 GHz. The fabricated Q-MOD achieves P1 dB improvement of more than 2.8 dB under the same condition. It also improves the output power with error vector magnitude (EVM) of 3.0% (Pout@EVM=3.0%), and achieves the Pout improvement of more than 2.7 dB under the modulation conditions of UHF wireless system (OFDM/16QAM, 0.4 GHz), W-CDMA (HPSK/QPSK, 0.8 GHz/1.95 GHz) and wireless-LAN (OFDM/64QAM, 5.2 GHz/5.8 GHz).

This paper describes downlink throughput performances measured in a mobile broadband wireless access (MBWA) system field trial with Fast Low-latency Access with Seamless Handoff Orthogonal Frequency Division Multiplexing (FLASH-OFDM). The field trial results show that the downlink cell sizes are 0.4 km2, 0.6 km2, and 1.7 km2 when the sector antenna heights are 19 m, 58 m, and 84 m, respectively, assuming the following items. (1) The cell shape is circular. (2) The cell edge is defined as the location where the average downlink throughput is 1.5 Mbit/s.

A constant voltage/constant current (CV/CC) parallel operation heterojunction bipolar transistor (HBT) power amplifier (PA) configuration is presented, and its design method is described. A resistor base feed (CC mode) HBT is connected to an inductor base feed (CV mode) HBT in parallel, and compensates the gain expansion of the CV mode HBT due to near class-B operation. By adding CC mode HBT, the total quiescent current can be decreased from 32 mA to 23 mA with adjacent channel leakage power ratio (ACPR) < -40.0 dBc. At the maximum output power region, the fabricated PA achieves output power (Pout) of 26.8 dBm and power added efficiency (PAE) of 42.0% with ACPR of -40.0 dBc, and shows the comparable performances with a conventional PA using CV mode HBT.

In order to realize millimeter-wave (MMW) 3-D system-in-package (SiP) front-end modules, we propose a 60-GHz band copper ball vertical interconnection structure, which interconnects between vertically stacked substrates. The structure enables ICs to be placed between the vertically stacked substrates. Since the diameter of the copper balls must exceed the thickness of the ICs, the distance between the substrates in the modules is larger than that of the flip-chip interconnection widely used in the MMW-band. Therefore, the conventional flip-chip interconnection does not scale for the interconnection between the substrates in MMW 3-D SiP front-end modules. The layout of grounded copper balls and the patterns of inner ground layers in the upper/lower substrates are designed using 3-D electromagnetic field simulation. The designed structure allows less than 1 dB transmission loss up to 71.1 GHz, compared with a through transmission line. The result is verified with fabrication and measurement and confirms the feasibility of MMW 3-D SiP front-end modules.

This paper proposes 1-bit feedforward distortion compensation for digital radio frequency conversion (DRFC) with 1-bit bandpass delta-sigma modulation (BP-DSM). The 1-bit BP-DSM allows direct RF signal transmission from a digitally modulated signal. However, it has been previously reported that 1-bit digital pulse trains with non-ideal rectangle waveform cause spectrum regrowth. The proposed architecture adds a feedforward path with another 1-bit BP-DSM and so can cancel out the distortion components at any target carrier frequency. Both the main signal and the distortion compensation signal are 1-bit digital pulse trains and so no additional analog RF circuit is required for distortion compensation. Simulation results show that the proposed method holds the adjacent channel leakage ratio to 60dB for LTE signal transmission. A prototype of the proposed 1-bit DRFC with an additional 1-bit BP-DSM in the feedforward path shows an ACLR of 50dB, 4dB higher than that of the conventional 1-bit DRFC.

A low cost, ultra small Radio Frequency (RF) transceiver module with integrated antenna is one of the key technologies for short range millimeter-wave wireless communication. This paper describes a 60 GHz-band transmitter module with integrated dipole antenna. The module consists of three pieces of low-cost organic resin substrate. These substrates are vertically stacked by employing Cu ball bonding 3-dimensional (3-D) system-in-package (SiP) technology and the MMIC's are mounted on each organic substrates by using Au-stud bump bonding (SBB) technique. The planer dipole antenna is fabricated on the top of the stacked organic substrate to avoid the influence of the grounding metal on the base substrate. At 63 GHz, maximum actual gain of 6.0 dBi is obtained for fabricated planar dipole antenna. The measured radiation patterns are agreed with the electro-magnetic (EM) simulated result, therefore the other RF portion of the 3-D front-end module, such as flip chip mounted IC's on the top surface of the module, does not affect the antenna characteristics. The results show the feasibility of millimeter-wave low cost, ultra small antenna integrated module using stacked organic substrates.

The 1-bit band-pass delta-sigma modulator (BP-DSM) achieves high resolution if it uses an oversampling technique. This method can generate concurrent dual-band RF signals from a digitally modulated signal using a 1-bit digital pulse train. It was previously reported that the adjacent channel leakage ratio (ACLR) deteriorates owing to the asymmetrical waveform created by the pulse transition mismatch error of the rising and falling waveforms in the time domain and that the ACLR can be improved by distortion compensation. However, the reported distortion compensation method can only be performed for single-band transmission, and it fails to support multi-band transmission because the asymmetrical waveform compensated signal extends over a wide frequency range and is itself a harmful distortion outside the target band. Unfortunately, the increase of out-of-band power causes the BP-DSM unstable. We therefore propose a distortion compensator for a concurrent dual-band 1-bit BP-DSM that consists of a noise transfer function with a quasi-elliptic filter that can control the out-of-band gain frequency response against out-of-band oscillation. We demonstrate that dual-band LTE signals, each with 40MHz (2×20MHz) bandwidth, at 1.5 and 3.0GHz, can be compensated concurrently for spurious distortion under various combinations of rising and falling times and ACLR of up to 48dB, each with 120MHz bandwidth, including the double sided adjacent channels and next adjacent channels, is achieved.

We have already proposed synchronized spread spectrum code division multiple access (SS-CDMA) for the Quasi-Zenith Satellite System (QZSS) safety confirmation system to be used in times of great disaster. In this system, the satellite reception timings of all uplink signals are synchronized using a transmission timing control method in order to realize high-density user multiple access. An issue that should be addressed in order for this system to be viable is the error that can occur in the satellite reception timing. This error occurs due to the terminal time deviation and the error in calculating the propagation delay to the satellite. In this paper, we measure the terminal time deviation and the propagation delay calculation error at the same time by using the same receivers and evaluate the satellite reception timing error of the uplink signal. By this measurement, it is shown that satellite reception timing error within 50ns can be realized in 99.98% of mobile terminals. This shows that the synchronized SS-CDMA with the transmission timing control method has a potential to realize the QZSS short message system with high-density user multiple access.

This paper presents a theoretical analysis of a tunable resonator using a coupled line and switches for the first time. The tunable resonator has the capability to tune its resonant frequency and bandwidth. The resonator has two suitable features on its tunable capability. The first feature is that the resonator retains its resonant frequency during bandwidth tuning. The second feature is that the on-state switch for tuning the bandwidth does not affect the insertion loss at the resonant frequency. These features are theoretically confirmed by its mathematically derived input impedance. The results from electromagnetic simulation and measurement of the fabricated tunable resonator also confirm these features. The fabricated tunable resonator changes the resonant frequency from 2.6 GHz to 6.4 GHz and bandwidth between 9% and 55%.

A 2-D beam scanning array antenna fed by a compact 16-way 2-D beamforming network (BFN) designed in Broadside Coupled Stripline (BCS) is addressed. The proposed 16-way 2-D BFN is formed by interconnecting two groups of 4x4 Butler Matrix (BM). Each group is composed of four compact 4x4 BMs. The critical point of the design is to propose a simple and compact 4x4 BM without crossover in BCS to achieve a better transmission coefficient of the 16-way 2-D BFN with reduced size of merely 0.8λ0×0.8λ0×0.04λ0. Moreover, the complexity of the interface connection between the 2-D BFN and the 4x4 patch array antenna is reduced by using probe feeding. The 16-way 2-D BFN is able to produce the phase shift of ±45°, and ±135° in x- and y- directions. The 2-D BFN is easily integrated under the 4x4 patch array to form a 2-D phased array capable of switching 16 beams in both elevation and azimuth directions. The area of the proposed 2-D beam scanning array antenna module has been significantly reduced to 2λ0×2λ0×0.04λ0. A prototype operating in the frequency range of 4-6GHz is fabricated and measured to validate the concept. The measurement results agree well with the simulations.

In this article, a new Beamforming Network (BFN) realized in Broadside Coupled Stripline (BCS) is proposed to feed 1×4 and 2×2 arrays antenna at 28 GHZ-Band. The new BFN is composed only of couplers and phase shifters. It doesn't require any crossover compared to the conventional Butler Matrix (BM) which requires two crossovers. The tight coupling and low loss characteristics of the BCS allow a design of a compact and wideband BFN. The new BFN produces the phase differences of (±90°) and (±45°, ±135°) respectively in x- and y-directions. Its integration with a 1×4 linear array antenna reduces the array area by 70% with an improvement of the gain performance compared with the conventional array. The integration with a 2×2 array allows the realization of a full 2-D beam scanning. The proposed concept has been verified experimentally by measuring the fabricated prototypes of the BFN, the 1-D and 2-D patch arrays antennas. The measured 11.5 dBi and 11.3 dBi maximum gains are realized in θ0 = 14° and (θ0, φ0) = (45°,345°) directions respectively for the 1-D and 2-D patch arrays. The physical area of the fabricated BFN is only (0.37λ0×0.3λ0×0.08λ0), while the 1-D array and 2-D array antennas areas without feeding transmission lines are respectively (0.5λ0×2.15λ0×0.08λ0) and (0.9λ0×0.8λ0×0.08λ0).

A 2 to 5 GHz-band self frequency dividing quadrature mixer utilizing current re-use configuration with small size and broad band operation is proposed for a direct conversion receiver and a low-IF receiver of cognitive radio. The proposed mixer operates at twice the LO frequency by directly using a static type flip-flop frequency divider as the LO switching circuit for quadrature signal generation. The current re-use configuration is realized because the dc current of the frequency divider and the RF common-emitter amplifier share the same current flow path. Simulations and experiments verify that the proposed mixer offers broad band operation, miniaturization, and low power consumption. The mixer IC fabricated by 0.35 µm SiGe-BiCMOS technology achieved the conversion gain of 20.6 dB, noise figure of 11.9 dB and EVM for π/4-shift QPSK signal of 4.4% at 2.1 GHz with power consumption of 15 mW and size of 0.22 0.31 mm2. For the confirmation of broad band operation, the characteristics of conversion gain and noise figure were measured at 5.2 GHz. The proposed mixer could operate at 5.2 GHz with enough conversion gain, but the noise figure was inferior to that of 2.1 GHz. Therefore the further investigation and improvement about the noise figure will be needed for higher frequency.

A novel analysis method of the intermodulation (IM) and the noise power ratio (NPR) of multiple-carrier amplifiers is descrided. This method, based on Discrete Fourier Transform, allows an accurate calculation of IM and NPR of the amplifier having multiple carriers by directly using measured single-carrier amplitude and phase characteristics. This method has an outstanding feature in that it can be applied to the general case of n carriers having an arbitrary power level as long as frequency-dependence of amplitude and phase characteristics is negligibly small. Applying this method to the linearized amplifier, a good agreement between measured and calculated results for IM3, IM5, and NPR has been obtained for operation from linear up to saturation, which shows this method would be a good candidate for calculating IM and NPR of multiple-carrier amplifiers.