SLM (Scalable Logic Module) is a fine-grained reconfigurable logic developed by Kumamoto University. Its small configuration information size characterizes it, resulting in a smaller area for logic cells. We have been developing an SoC-type FPGA called SLMLET to take advantage of SLM. It keeps multiple sets of configuration data in the memory module inside the chip in a compressed form and exchanges them quickly. This paper proposes a simple run-length compression technique called TLC (Tag Less Compression). It achieved a 1.01-3.06 compression ratio, is embedded in the prototype of the SLMLET, and is available now. Then, we propose DMC (Duplication Module Compression), which uses repeatedly appearing patterns in the SLM configuration data. The DMC achieves a better compression ratio for complicated designs that are hard to compress with TLC.

In this paper, we propose a novel communication scheme that combines reconfigurable intelligent surface with transmitted adaptive space shift keying (RIS-TASSK), where the number of active antennas is not fixed. In each time slot, the desired candidate antenna or antenna combination will be selected from all available antenna combinations for conveying information bits. Besides, an antenna selection method based on channel gains is proposed for RIS-TASSK to improve the bit error rate (BER) performance and decrease the complexity, respectively. By comparing with the RIS-aided transmitted space shift keying and RIS-aided transmitted generalized space shift keying schemes, the simulation and theoretical results show that the proposed scheme has better BER performance and appropriate complexity.

High altitude platform (HAP), known as line-of-sight dominated communications, effectively enhance the spectral efficiency of wireless networks. However, the line-of-sight links, particularly in urban areas, may be severely deteriorated due to the complex communication environment. The reconfigurable intelligent surface (RIS) is employed to establish the cascaded-link and improve the quality of communication service by smartly reflecting the signals received from HAP to users without direct-link. Motivated by this, the joint precoding scheme for a novel RIS-aided beamspace HAP with non-orthogonal multiple access (HAP-NOMA) system is investigated to maximize the minimum user signal-to-leakage-plus-noise ratio (SLNR) by considering user fairness. Specifically, the SLNR is utilized as metric to design the joint precoding algorithm for a lower complexity, because the isolation between the precoding obtainment and power allocation can make the two parts be attained iteratively. To deal with the formulated non-convex problem, we first derive the statistical upper bound on SLNR based on the random matrix theory in large scale antenna array. Then, the closed-form expressions of power matrix and passive precoding matrix are given by introducing auxiliary variables based on the derived upper bound on SLNR. The proposed joint precoding only depends on the statistical channel state information (SCSI) instead of instantaneous channel state information (ICSI). NOMA serves multi-users simultaneously in the same group to compensate for the loss of spectral efficiency resulted from the beamspace HAP. Numerical results show the effectiveness of the derived statistical upper bound on SLNR and the performance enhancement of the proposed joint precoding algorithm.

The concept of dual function radar-communication (DFRC) provides solution to the problem of spectrum scarcity. This paper examines a multiple-input multiple-output (MIMO) DFRC system with the assistance of a reconfigurable intelligent surface (RIS). The system is capable of sensing multiple spatial directions while serving multiple users via orthogonal frequency division multiplexing (OFDM). The objective of this study is to design the radiated waveforms and receive filters utilized by both the radar and users. The mutual information (MI) is used as an objective function, on average transmit power, for multiple targets while adhering to constraints on power leakage in specific directions and maintaining each user’s error rate. To address this problem, we propose an optimal solution based on a computational genetic algorithm (GA) using bisection method. The performance of the solution is demonstrated by numerical examples and it is shown that, our proposed algorithm can achieve optimum MI and the use of RIS with the MIMO DFRC system improving the system performance.

Cooperative Communication is one of the most effective techniques to improve the desired signal quality of the typical user. This paper studies an indoor cellular network system that deploys the Reconfigurable Intelligent Surfaces (RIS) at the position of BSs to enable the cooperative features. To evaluate the network performance, the coverage probability expression of the typical user in the indoor wireless environment with presence of walls and effects of Rayleigh fading is derived. The analytical results shows that the RIS-assisted system outperforms the regular one in terms of coverage probability.

Despite the appealing advantages of reconfigurable intelligent surfaces (RIS) aided mmWave communications, there remain practical issues that need to be addressed before the large-scale deployment of RISs in future wireless networks. In this study, we jointly consider the non-neglectable practical issues in a multi-RIS-aided mmWave system, which can significantly affect the secrecy performance, including the high computational complexity, imperfect channel state information (CSI), and finite resolution of phase shifters. To solve this non-convex challenging stochastic optimization problem, we propose a robust and low-complexity algorithm to maximize the achievable secrete rate. Specially, by combining the benefits of fractional programming and the stochastic successive convex approximation techniques, we transform the joint optimization problem into some convex ones and solve them sub-optimally. The theoretical analysis and simulation results demonstrate that the proposed algorithms could mitigate the joint negative effects of practical issues and yielded a tradeoff between secure performance and complexity/overhead outperforming non-robust benchmarks, which increases the robustness and flexibility of multiple RIS deployments in future wireless networks.

This paper proposes multi-gate reconfigurable (RECON) cells and a technology remapping approach using them as spare cells for post-mask functional engineering change orders (ECOs). With the rapid increase in circuit complexity, ECOs often occur in the post-mask stage of LSI designs. To deal with post-mask ECOs at a low cost, only the metal layers are redesigned by making functional changes using spare cells. For this purpose, 2T/4T/6T-RECON cells were proposed as reconfigurable spare cells. However, conventional RECON cells are used to implement single functions, which may result in unused transistors in the cells. In addition, the number of 2T/4T/6T-RECON spare cells used for post-mask ECOs varies greatly depending on the circuit to be implemented and the type of ECO that occurs. Therefore, functional ECOs may fail due to a lack of certain types of RECON cells, even if other types of RECON cells remain. To solve this problem, we propose multi-gate RECON cells that implement multiple functions in a single RECON cell while retaining the layouts of conventional 4T/6T-RECON base cells, and a technology remapping approach using them. The proposed approach not only reduces the number of used spare cells for modifications but also allows the flexible use of spare cells to fix them with less increase in wire length and delay. Experimental results have confirmed that the functional ECO success ratio is increased by 4.8pt on average and the total number of used spare cells is reduced by 5.6% on average. It has also been confirmed that the increase in wire length is reduced by 17.4% on average and the decrease in slack is suppressed by 21.6% on average.

Memory-based Programmable Logic Device (MPLD) is a new type of reconfigurable device constructed using a general SRAM array in a unique interconnect configuration. This research aims to propose approaches to guarantee the long-term reliability of MPLDs, including a test method to identify interconnect defects in the SRAM array during the production phase and a delay monitoring technique to detect aging-caused failures. The proposed test method configures pre-generated test configuration data into SRAMs to create fault propagation paths, applies an external walking-zero/one vector to excite faults, and identifies faults at the external output ports. The proposed delay monitoring method configures a novel ring oscillator logic design into MPLD to measure delay variations when the device is in practical use. The logic simulation results with fault injection confirm the effectiveness of the proposed methods.

Thanks to the development of the 6th generation mobile network that makes it possible for us to move towards an intelligent ubiquitous information society, among which some novel technologies represented by cell-free network has also attracted widespread academic attention. Cell-free network has brought distinguished gains to the network capacity with its strong ability against inter-cell interference. Unfortunately, further improvement demands more base stations (BSs) to be settled, which incurs steep cost increase. To address this issue, reconfigurable intelligent surface (RIS) with low cost and power consumption is introduced in this paper to replace some of the trivial BSs in the system, then, a RIS-aided cell-free network paradigm is formulated. Our objective is to solve the weighted sum-rate (WSR) maximization problem by jointly optimizing the beamforming design at BSs and the phase shift of RISs. Due to the non-convexity of the formulated problem, this paper investigates a joint optimizing scheme based on block coordinate descent (BCD) method. Subsequently, on account of the majority of the precious work reposed perfect channel state information (CSI) setup for the ultimate performance, this paper also extends the proposed algorithm to the case wherein CSI is imperfect by utilizing successive convex approximation (SCA). Finally, simulation results demonstrate that the proposed scheme shows great performance and robustness in perfect CSI scenario as well as the imperfect ones.

Wireless technology improvements have been continually increasing, resulting in greater needs for system design and implementation to accommodate all newly emerging standards. As a result, developing a system that ensures compatibility with numerous wireless systems has sparked interest. As a result of their flexibility and scalability over alternative wireless design options, software-defined radios (SDRs) are highly motivated for wireless device modelling. This research paper delves into the difficulties of designing a reconfigurable multi modulation baseband modulator for SDR systems that can handle a variety of wireless protocols. This research paper has proposed an area-efficient Reconfigurable Baseband Modulator (RBM) model to accomplish multi modulation scheme and resolve the adaptability and flexibility issues with the wide range of wireless standards. This also presents the feasibility of using a multi modulation baseband modulator to maximize adaptability with the least possible computational complexity overhead in the SDR system for next-generation wireless communication systems and provides parameterization. Finally, the re-configurability is evaluated concerning the appropriate symbols generations and analyzed its performance metrics through hardware synthesize results.

A domain-specific networking platform based on optically interconnected reconfigurable communication processors is proposed. Some application examples of the reconfigurable communication processor and networking experiment results are presented.

In this paper, a novel reconfigurable intelligent surface (RIS)-aided full-duplex (FD) cooperative non-orthogonal multiple access (CNOMA) network is investigated over Nakagami-m fading channels, where two RISs are employed to help the communication of paired users. To evaluate the potential benefits of our proposed scheme, we first derive the closed-form expressions of the outage probability. Then, we derive users' diversity orders according to the asymptotic approximation at high signal-to-noise-ratio (SNR). Simulation results validate our analysis and reveal that users' diversity orders are affected by their channel fading parameters, the self-interference of FD, and the number of RIS elements.

Reconfigurable intelligent surface (RIS) has the capability of boosting system performance by manipulating the wireless propagation environment. This paper investigates a downlink RIS-aided non-orthogonal multiple access (NOMA) system, where a RIS is deployed to enhance physical-layer security (PLS) in the presence of an eavesdropper. In order to improve the main link's security, the RIS is deployed between the source and the users, in which a reflecting element separation scheme is developed to aid data transmission of both the cell-center and the cell-edge users. Additionally, the closed-form expressions of secrecy outage probability (SOP) are derived for the proposed RIS-aided NOMA scheme. To obtain more deep insights on the derived results, the asymptotic performance of the derived SOP is analyzed. Moreover, the secrecy diversity order is derived according to the asymptotic approximation in the high signal-to-noise ratio (SNR) and main-to-eavesdropper ratio (MER) regime. Furthermore, based on the derived results, the power allocation coefficient and number of elements are optimized to minimize the system SOP. Simulations demonstrate that the theoretical results match well with the simulation results and the SOP of the proposed scheme is clearly less than that of the conventional orthogonal multiple access (OMA) scheme obviously.

An approach to dedicated computers is discussed in this study as a possibility for portable, low-cost, and low-power consumption high-performance computing technologies. Particularly, dataflow architecture dedicated computer of the finite integration technique (FIT) for 2D magnetostatic field simulation is considered for use in industrial applications. The dataflow architecture circuit of the BiCG-Stab matrix solver of the FIT matrix calculation is designed by the very high-speed integrated circuit hardware description language (VHDL). The operation of the dedicated computer's designed circuit is considered by VHDL logic circuit simulation.

Intelligent reconfigurable surfaces (IRS) have attracted much attention from both industry and academia due to their performance improving capability and low complexity for 6G wireless communication systems. In this letter, we introduce an IRS-assisted space-time line code (STLC) technique. The STLC was introduced as a promising technique to acquire the optimal diversity gain in 1×2 single-input multiple-output (SIMO) channel without channel state information at receiver (CSIR). Using the cosine similarity theorem, we propose a novel phase-steering technique for the proposed IRS-assisted STLC technique. We also mathematically characterize the proposed IRS-assisted STLC technique in terms of outage probability and bit-error rate (BER). Based on computer simulations, it is shown that the results of analysis shows well match with the computer simulation results for various communication scenarios.

The existing research on Amdahl's law is limited to multi/many-core processors, and cannot be applied to the important parallel processing architecture of coarse-grained reconfigurable arrays. This paper studies the relation between the multi-level parallelism of block cipher algorithms and the architectural characteristics of coarse-grain reconfigurable arrays. We introduce the key variables that affect the performance of reconfigurable arrays, such as communication overhead and configuration overhead, into Amdahl's law. On this basis, we propose a performance model for coarse-grain reconfigurable block cipher array (CGRBA) based on the extended Amdahl's law. In addition, this paper establishes the optimal integer nonlinear programming model, which can provide a parameter reference for the architecture design of CGRBA. The experimental results show that: (1) reducing the communication workload ratio and increasing the number of configuration pages reasonably can significantly improve the algorithm performance on CGRBA; (2) the communication workload ratio has a linear effect on the execution time.

Herein, a novel self-oscillating active integrated array antenna (AIAA) is proposed for beam switching X-band applications. The proposed AIAA comprises four linearly polarized microstrip antenna elements, a Gunn oscillator, two planar magic-Ts, and two single-pole single-throw (SPST) switches. The in/anti-phase signal combination approach employing planar magic-Ts is adopted to attain bidirectional radiation patterns in the φ =90° plane with a simple structure. The proposed antenna can switch its beam using the SPST switches. The antenna is analyzed through simulations, and a prototype of the antenna is fabricated and tested to validate the concept. The proposed concept is found to be feasible; the prototype has an effective isotropic radiated power of +15.98dBm, radiated power level of +4.28dBm, and cross-polarization suppression of better than 15dB. The measured radiation patterns are in good agreement with the simulation results.

Elliptic curve cryptography (ECC), one of the asymmetric cryptography, is widely used in practical security applications, especially in the Internet of Things (IoT) applications. This paper presents a low-power reconfigurable architecture for ECC, which is capable of resisting simple power analysis attacks (SPA) and can be configured to support all of point operations and modular operations on 160/192/224/256-bit field orders over GF(p). Point multiplication (PM) is the most complex and time-consuming operation of ECC, while modular multiplication (MM) and modular division (MD) have high computational complexity among modular operations. For decreasing power dissipation and increasing reconfigurable capability, a Reconfigurable Modular Multiplication Algorithm and Reconfigurable Modular Division Algorithm are proposed, and MM and MD are implemented by two adder units. Combining with the optimization of operation scheduling of PM, on 55 nm CMOS ASIC platform, the proposed architecture takes 0.96, 1.37, 1.87, 2.44 ms and consumes 8.29, 11.86, 16.20, 21.13 uJ to perform one PM on 160-bit, 192-bit, 224-bit, 256-bit field orders. It occupies 56.03 k gate area and has a power of 8.66 mW. The implementation results demonstrate that the proposed architecture outperforms the other contemporary designs reported in the literature in terms of area and configurability.

Accumulate Repeat-4 Jagged-Accumulate (AR4JA) codes, which are channel codes designed for deep-space communications, are a series of QC-LDPC codes. Structures of these codes' generator matrix can be exploited to design reconfigurable encoders. To make the decoder reconfigurable and achieve shorter convergence time, turbo-like decoding message passing (TDMP) is chosen as the hardware decoder's decoding schedule and normalized min-sum algorithm (NMSA) is used as decoding algorithm to reduce hardware complexity. In this paper, we propose a reconfigurable decoder and present its FPGA implementation results. The decoder can achieve throughput greater than 74 Mbps.

For high definition (HD) videos, the 3D-High Efficiency Video Coding (3D-HEVC) reference algorithm incurs dramatically highly computation loads. Therefore, with the demands for the real-time processing of HD video, a hardware implementation is necessary. In this paper, a reconfigurable architecture is proposed that can support both median filtering preprocessing and mean filtering preprocessing to satisfy different scene depth maps. The architecture sends different instructions to the corresponding processing elements according to different scenarios. Mean filter is used to process near-range images, and median filter is used to process long-range images. The simulation results show that the designed architecture achieves an averaged PSNR of 34.55dB for the tested images. The hardware design for the proposed virtual view synthesis system operates at a maximum clock frequency of 160MHz on the BEE4 platform which is equipped with four Virtex-6 FF1759 LX550T Field-Programmable Gate Array (FPGA) for outputting 720p (1024×768) video at 124fps.