The load-independent zero-voltage switching class-E inverter has garnered considerable interest as an essential component in wireless power transfer systems. This inverter achieves high efficiency across a broad spectrum of load conditions by incorporating a load adjustment circuit (LAC) subsequent to the resonant filter. Nevertheless, the presence of the LAC influences the output impedance of the inverter, thereby inducing a divergence between the targeted and observed output power, even in ideal lossless simulations. Consequently, iterative adjustments to component values are required via an LC element implementation. We introduce a novel design methodology that incorporates an external quality factor on the side of the resonant filter, inclusive of the LAC. Thus, the optimized circuit achieves the intended output power without necessitating alterations in component values.

This paper introduces a wireless-powered relay transceiver designed to extend 5G millimeter-wave coverage. It employs an on-chip butler matrix, enabling beam control-free operation. The prototype includes PCB array antennas and on-chip butler matrix and rectifiers manufactured using a Si CMOS 65 nm process. The relay transceiver performs effectively in beam angles from -45° to 45°. In the 24 GHz wireless power transmission (WPT) mode, it generates 0.12 mW with 0 dBm total input power, boasting an RF-DC conversion efficiency of 12.2%. It also demonstrates communication performance at 28 GHz in both RX and TX modes with a 100 MHz bandwidth and 64QAM modulation.

A wireless sensor terminal module of 5cc size (2.5 cm × 2.5 cm × 0.8 cm) that does not require a battery is proposed by integrating three kinds of circuit technologies. (i) a low-power sensor interface: an FM modulation type CMOS sensor interface circuit that can operate with a typical power consumption of 24.5 μW was fabricated by the 0.7-μm CMOS process technology. (ii) power supply to the sensor interface circuit: a wireless power transmission characteristic to a small-sized PCB spiral coil antenna was clarified and applied to the module. (iii) wireless sensing from the module: backscatter communication technology that modulates the signal from the base terminal equipment with sensor information and reflects it, which is used for the low-power sensing operation. The module fabricated includes a rectifier circuit with the PCB spiral coil antenna that receives wireless power transmitted from base terminal equipment by electromagnetic resonance coupling and converts it into DC power and a sensor interface circuit that operates using the power. The interface circuit modulates the received signal with the sensor information and reflects it back to the base terminal. The module could achieve 100 mm communication distance when 0.4 mW power is feeding to the sensor terminal.

This paper presents the design of a capacitive coupler for underwater wireless power transfer focused on the landing direction of a drone. The main design feature is the relative position of power feeding/receiving points on the coupler electrodes, which depends on the landing direction of the drone. First, the maximum power transfer efficiencies of coupled lines with different feeding positions are derived in a uniform dielectric environment, such as that realized underwater. As a result, these are formulated by the coupling coefficient of the capacitive coupler, the unloaded qualify factor of dielectrics, and hyperbolic functions with complex propagation constants. The hyperbolic functions vary depending on the relative positions and whether these are identical or opposite couplers, and the efficiencies of each coupler depend on the type of water, such as seawater and tap water. The design method was demonstrated and achieved the highest efficiencies of 95.2%, 91.5%, and 85.3% in tap water at transfer distances of 20, 50, and 100 mm, respectively.

The misalignment of a coupler is a significant issue for capacitive wireless power transfer (WPT). This paper presents a capacitive WPT system specifically designed for underwater drones operating in flowing freshwater environments. The primary design features include a capacitive coupler with an opposite relative position between feeding and receiving points on the coupler electrode, two phase compensation circuits, and a load-independent inverter. A stable and energy-efficient power transmission is achieved by maintaining a 90° phase difference on the coupler electrode in dielectrics with a large unloaded quality factor (Q factor), such as in freshwater. Although a 622-mm coupler electrode is required at 13.56MHz, the phase compensation circuits can reduce to 250mm as one example, which is mountable to small underwater drones. Furthermore, the electricity waste is automatically reduced using the constant-current (CC) output inverter in the event of misalignment where efficiency drops occur. Finally, their functions are simulated and demonstrated at various receiver positions and transfer distances in tap water.

Currently, wireless power transmission technology is being developed for capsule endoscopes. By removing the battery, the capsule endoscope is miniaturized, the number of images that can be taken increases, and the risk of harmful substances leaking from the battery when it is damaged inside the body is avoided. Furthermore, diagnostic accuracy is improved by adjusting the directivity of radio waves according to the position of the capsule endoscope to improve efficiency and adjusting the number of images to be taken according to position by real-time position estimation. In this study, we report the result of position estimation in a high-definition numerical human body model and in an experiment on an electromagnetic phantom.

This study proposes a design method for a rectifier circuit that can be rapidly charged by focusing on the design-load value of the circuit and the load fluctuation of a storage capacitor. The design-load value is suitable for rapidly charging the capacitor. It can be obtained at the lowest reflection condition and estimated according to the circuit design. This is a conventional method for designing the rectifier circuit using the optimum load. First, we designed rectifier circuits for the following three cases. The first circuit design uses a load set to 10 kΩ. The second design uses a load of 30 kΩ that is larger than the optimum load. The third design utilizes a load of 3 kΩ. Then, we measure the charging time to design the capacitor on each circuit. Consequently, the results show that the charge time could be shortened by employing the design-load value lower than that used in the conventional design. Finally, we discuss herein whether this design method can be applied regardless of the rectifier circuit topology.

This paper presents the feasibility of a capacitive coupler utilizing an electric double layer for wireless power transfer under seawater. Since seawater is an electrolyte solution, an electric double layer (EDL) is formed on the electrode surface of the coupler in direct current. If the EDL can be utilized in radio frequency, it is possible that high power transfer efficiency can be achieved under seawater because a high Q-factor can be obtained. To clarify this, the following steps need taking; First, measure the frequency characteristics of the complex permittivity in seawater and elucidate the behaviors of the EDL from the results. Second, clarify that EDL leads to an improvement in the Q-factor of seawater. It will be shown in this paper that capacitive coupling by EDL occurs using two kinds of the coupler models. Third, design a coupler with high efficiency as measured by the Q-factor and relative permittivity of EDL. Last, demonstrate that the designed coupler under seawater can achieve over 85% efficiency at a transfer distance of 5 mm and feasibility of the coupler with EDL.

In recent years, capsule endoscopy has attracted attention as one of the medical devices that examine internal digestive tracts without burdening patients. Wireless power transmission of the capsule endoscope has been researched now, and the power transmission efficiency can be improved by knowing the capsule location. In this paper, we develop a localization method wireless power transmission. Therefore, a simple algorithm for using received signal strength (RSS) has been developed so that position estimation can be performed in real time, and the performance is evaluated by performing three-dimensional localization with eight receiving antennas.

This paper presents the design of a capacitive coupler for underwater wireless power transfer (U-WPT) focusing on kQ product. Power transfer efficiency hinges on the coupling coefficient k between the couplers and Q-factor of water calculated from the complex permittivity. High efficiency can be achieved by handling k and the Q-factor effectively. First, the pivotal elements on k are derived from the equivalent circuit of the coupler. Next, the frequency characteristic of the Q-factor in tap water is calculated from the measured results. Then, the design parameters in which kQ product has the maximal values are determined. Finally, it is demonstrated that the efficiency of U-WPT with the capacitive coupling designed by our method achieves approximately 80%.

A rotating shaft with attached sensors is wrapped in a two-dimensional waveguide sheet through which the data and power are wirelessly transmitted. A retrodirective transponder array affixed to the sheet beamforms power to the moving sensor to eliminate the need for a battery. A universal on-sheet reference scheme is proposed for calibrating the transponder circuit delay variation and eliminating a crystal oscillator from the sensor. A base signal transmitted from the on-sheet reference device is used for generating the pilot signal transmitted from the sensor and the power signal transmitted from the transponder. A 0.18-µm CMOS transponder chip and the sheet with couplers were fabricated. The coupler has three resonant frequencies used for the proposed system. The measured propagation gain of the electric field changes to less than ±1.5dB within a 2.0-mm distance between the coupler and the sheet. The measured power transmission efficiency with beamforming is 23 times higher than that without it. Each transponder outputs 1W or less for providing 3mW to the sensor.

A two-dimensional (2D) wireless power transmission (WPT) system that handles a wide range of transmitted and received power is proposed and evaluated. A transmitter outputs the power to an arbitrary position on a 2D waveguide sheet by using a beam-forming technique. The 2D waveguide sheet does not require an absorber on its edge. The minimum propagation power on the sheet is increased 18 times by using the beam-forming technique. Power amplifier (PA) efficiency was improved from 19% to 46% when the output power was 10dB smaller than peak power due to the use of a PA supply-voltage and input power control method. Peak PA efficiency was 60%. A receiver inputs a wide range of power levels and drives various load impedances with a parallel rectifier. This rectifier enables a number of rectifying units to be tuned dynamically. The rectifier efficiency was improved 1.5 times while input power range was expanded by 6dB and the load-impedance range was expanded fourfold. The rectifier efficiency was 66-73% over an input power range of 18-36dBm at load impedances of 100 and 400Ω.

A novel spatially modulated communication method, appropriate for wireless power transmission applications at 5.8GHz, is proposed using dual scatterers embedded with lumped elements. Analytical expression for the received wave in the spatial modulation is derived, and the characteristics are verified with simulation and measurement by varying the embedded capacitor. The maximum measured variation of the received voltage is more than 15dB and that of the phase is more than 270 degrees at 5.8GHz. The estimated amplitude modulation factor is more than 70%. Using the data obtained, we estimate the practical received waveforms modulated by the applied voltage to a varactor for the amplitude modulation scheme.

A plane coupler has been developed for a two-dimensional (2D) wireless power transmission. This coupler can construct a continuous wireless power transmission system for mobile devices due to its small, light characteristics. This coupler has two elements connected with a 2D waveguide sheet, and coupling capacitances between the elements and the sheet decrease the coupler size by reducing their resonance frequencies. A propagation loss of -10.0 dB is obtained using the small 0.025-λ2 coupler. Continuous operation of the mobile device is demonstrated by applying wireless power transmission to the 2D waveguide sheet with the small plane coupler.

We propose a data transmission method for resonant wireless power transmission systems. In order to transmit data, we use the coils originally designed for power transmission, no additional antennas are required. We focus on uplink data transmission and adopt the load modulation technique. This configuration yields mid-range data transmission without transmitting power. In addition, the proposal enables simultaneous power feeding and uplink data transmission. We make a prototype demonstrating resonant wireless power transmission and measure its S-parameter under some load conditions. The results confirm the potential of load modulation in supporting uplink data transmission. Additionally, the results are elucidated by analyzing an equivalent circuit. Measured S-parameter and equivalent circuit response are found to be similar.

Compact and planar active integrated antenna arrays with a high power multi-stage amplifier were developed with effective heat sink mechanism. By attaching an aluminum plate to the backside of the creased amplifier circuit board, effective cooling can be achieved. The nonlinear behavior of the amplifier agrees well with the simulation based on the Angelov model. The high power amplifier circuit consisted of the three-stage amplifier and operated with an output power of 4 W per each element at 5.8 GHz. The 32-element active integrated antenna array stably operated with the output power of 120 W under the effective heat sink design. With a weight of 4 kg, the weight-to-output power ratio and the volume-to-output power ratio of the antenna array are 33.3 g/W and 54.5 cm3/W, respectively. Wireless power transmission was also successfully demonstrated.

A Cyclotron Wave Converter, having decreased magnetic intensity is discussed. Two microwave cavities with uniform and quadruple (or six-pole) electric field in the gap of interaction are used to transform microwave power into the kinetic power of the electron beam fast cyclotron wave. As a result of it, magnetic flux density occurs in two (or three) times lower. The latter is very important to create a compact, powerful and efficient microwave/DC power converters operating at different frequencies including short centimetric and long millimetric wavebands.

A rectenna element applicable to Stratosphere Radio Relay System was proposed and a fundamental microwave power transmission experiment was carried out at 2.45GHz using a rectenna array manufactured based on the proposal. The rectenna element consists of a circular microstrip patch and a rectifying circuit of novel balanced-type design. The circuit allows to mount a rectifier and circuit components just on one side of a substrate without through holes, and hence it must be easy to manufacture a rectenna even having a large aperture. It was verified by a preliminary experiment that the rectifying circuit can provide more than 1 W of DC output power using 8 Shottky diodes as a rectifier with microwave-DC conversion efficiency of 67%. Then, DC output power of 4W was obtained from the 4-element rectenna array in the microwave power transmission experiment carried out in a radio anechoic chamber. The data showed a feasibility of practical application of the microwave power transmission technique.