The monocone antenna is a type of monopole antenna that has wideband characteristics. This paper proposes a low-profile monocone antenna with a planar inverted-F structure. The characteristics of the proposed antenna are analyzed through a simulation. The results demonstrate that the low-profile antenna offers wideband performance, and the relative bandwidth of VSWR ≤ 2 is found to be more than 190%. In addition, miniaturization of the monocone antenna is elucidated. The proposed antenna is prototyped, and the validity of the simulation is verified through measurements.

This paper presents the detailed investigations on a simple multi-band method that allows inverted-F antennas (IFAs) to achieve good impedance matching in many different frequency bands. The impressive simplicity of the method arises from its sharing of a shorting strip among multiple branch elements to simultaneously generate independent resonant modes at arbitrary frequencies. Our simulation and measurement results clarify that, by adjusting the number of branch elements and their lengths, it is very easy to control both the total number of resonant modes and the position of each resonant frequency with impedance matching improved concurrently by adjusting properly the distance ds between the feeding and shorting points. The effectiveness of the multi-band method is verified in antenna miniaturization designs, not only in the case of handset antenna, but also in the design upon an infinite ground plane. Antenna performance and operation principles of proposed multi-band models in each case are analyzed and discussed in detail.

Platform-mounted small antennas increase dielectric loss and conductive loss and decrease the radiation efficiency. This paper proposes a novel antenna design method to improve radiation efficiency for platform-mounted small antennas by characteristic mode analysis. The proposed method uses mapping of modal weighting coefficient (MWC) and infinitesimal dipole and evaluate the metal casing with 100mm × 55mm × 23mm as a platform excited by an inverted-F antenna. The simulation and measurement results show that the radiation efficiency of 5% is improved with the whole system from 2.5% of the single antenna.

This paper presents a novel simultaneous decoupling and matching technique for transmitting (Tx) and receiving (Rx) ports in short-range multiple-input multiple-output (SR-MIMO) systems. The principal difference with conventional decoupling and matching network (DMN) approaches is that the proposed technique considers strong mutual coupling between closely-positioned Tx/Rx arrays, and the S-parameter variation due to the presence of each other's array. This technique has two stages; first, 180-degree hybrid couplers are connected to both Tx/Rx ports of a plane-symmetrical MIMO system. This decouples both Tx/Rx ports, and moreover, channels between them are orthogonalized. That is, the MIMO system is transformed into multi orthogonalized single-input single-output (SISO) systems. Second, Tx/Rx ports of each orthogonalized SISO system are simultaneously matched based on conjugate matching theory. Consequently, the transmission power of the short-range MIMO system is maximized. Numerical results show that the proposed technique realizes higher channel capacity than the conventional DMN; indeed it achieves the theoretically possible capacity. In addition to theoretical analyses, we provide an example for microstrip line (MSL) circuit implementation. This MSL model offers good simultaneous decoupling and matching performance yielding channel capacity comparable to that of an ideally-designed circuit model. This validates the implementation feasibility of the proposed technique.

We developed a mantle-cloak antenna by controlling the surface reactance of a dielectric-loaded dipole antenna. First, a mantle-cloak antenna with an assumed ideal metasurface sheet was designed, and band rejection characteristics were obtained by controlling the surface reactance of the mantle cloak. The variable range of the frequency spacing between the operating and stopband frequencies of the antenna was clarified by changing the value of the surface reactance. Next, a mantle-cloak antenna that uses vertical strip conductors was designed to clarify the characteristics and operating principle of the antenna. It was confirmed that the stopband frequency was 1130MHz, and the proposed antenna had a 36.3% bandwidth (|S11| ≤ -10dB) from 700 to 1010MHz. By comparing the |S11| characteristics and the input impedance characteristics of the proposed antenna with those of the dielectric-loaded antenna, the effect of the mantle cloak was confirmed. Finally, a prototype of the mantle-cloak antenna that uses vertical strip conductors was developed and measured to validate the simulation results. The measurement results were consistent with the simulation results.

As the capacity of a personal computer and workstation increases rapidly, many electromagnetic simulators solving antenna problems are widely used. In this paper, the IE3D, FIDELITY and HFSS electromagnetic simulators, which are commercial software products, are applied to the analysis of built-in antennas for handsets in the vicinity of the human body. The IE3D, FIDELITY and HFSS electromagnetic simulators are based on the methods of moment, FDTD (Finite Difference Time Domain) and FEM (Finite Element Method), respectively. Firstly, basic characteristics including the human body's effect of a popular built-in antenna for handset such as PIFA (Planar Inverted-F Antenna) are obtained by the IE3D, FIDELITY and HFSS electromagnetic simulators, and calculated results are compared with measured results. Secondly, on the basis of newly considered design concepts for a handset antenna, a folded loop antenna for handset, which we have proposed in order to reduce the influence of the human body, is taken as an example of a balance-fed antenna and is analyzed theoretically and experimentally including the influence of the human body. In a result, calculated results by these three kinds of electromagnetic simulators are in good agreement with measured results and it is confirmed that these simulators are very effective in analyzing the handset antenna in the vicinity of the human body.

Analysis of a novel folded loop antenna for handset is described along with the advanced design concept for handset antennas. The design concept shown in this paper meets the foremost requirement for handset antennas such as (1) small size and yet (2) has capability of mitigating degradation of antenna performance due to the body effect, and (3) of reducing SAR value in the human head at the handset talk position, in addition to the indispensable requirements for handset antennas such as (4) low profile, and (5) light weight. The technology applied is to make this antenna (a) an integrated structure, which is a typical application of the fundamental concept of making antennas small and (b) a balanced structure which has been proved to be very effective to satisfy the requirements (2) and (3). The antenna is essentially a two-wire transmission line, folded at about a quarter-wavelength to form a half-wave folded dipole, and yet appears to be a loop of one-wavelength. It does not have really a balanced structure, as is fed with an unbalanced line; however, the antenna structure itself can eliminate the unbalanced current flow on the feed line as in the balanced antenna system. Both theoretical and experimental analyses have been shown and the usefulness of the antenna is discussed. This paper may suggest the advanced technology and design concept that will be applied to the development of handset antennas toward the future.

This paper reviews antenna technologies for cellular phone terminal in Japan. In regard to the technologies two technical subjects are addressed: a diversity system and miniaturization of terminal size. These subjects provide motivation for studies on design methods for diversity antennas, development of built-in antennas, and control methods for surface current on terminal cavity. These studies are progressing.

Two types of 3D folded dipole antenna with feed line (FDAFL) were reported for a small terminal, which covered WiMAX 2.5/3.5GHz bands and WLAN 2.4GHz band. In this study, folded monopole antenna (FMA) is proposed as a variant of FDAFL. We show the broadband characteristics of FMA and determine the most suitable configuration of FMA array for realizing MIMO system. Also, a multiband variant is created by introducing a parasitic element to FMA. The result is a multiband FMA array with parasitic elements operating at 5GHz band of WiMAX and WLAN as well as WiMAX 2.5/3.5GHz bands and WLAN 2.4GHz band with total antenna efficiency of between 70% to 96% and the envelope correlation coefficient of less than 0.02. Finally, a prototype antenna is implemented, and we confirm the validity of the simulation by comparison to measured results.

This study presents a proposal for space-saving design of built-in antennas for handset terminals based on the concept of requisite design antenna volume. By investigating the relation between antenna input characteristic and electric near-field around the antenna element and surrounding components inside the terminal, and then evaluating the requisite design antenna volume, we propose the most effective deployment for both the antenna and surrounding components. The results show that our simple proposal can help reduced, by about 17% and 31.75%, the space that the antenna element actually requires at least for stable operation inside the terminal, in the single-band designs for the cellular 2GHz band (1920-2170MHz) and 800MHz band (830-880MHz), respectively. In the dual-band design, we verify that it can reduce, the antenna space by about 35.18%, and completely cover the two above cellular bands with good antenna performance.

In this paper, we propose a new method based on copula theory to evaluate the detection performance of a distributed-processing multistatic radar system (DPMRS). By applying the Gaussian copula to model the dependence of local decisions in a DPMRS as well as data fusion rules of AND, OR, and K/N, the performance of a DPMRS for detecting Swerling fluctuating targets can be easily evaluated even under non-Gaussian clutter with a nonuniform dependence matrix. The reliability and flexibility of this method are validated by applying the proposed method to a previous problem by other authors, and our other investigation results indicate its high potential for evaluating DPMRS performance in various cases involving different models of target and clutter.

A folded loop antenna for handsets has already been introduced and shown as one of balance-fed antennas for handsets, which is very effective to mitigate the antenna performance degradation due to the body effect. In order to meet the requirements for the latest handsets such as low profile and small size, a folded loop antenna is modified. The antenna, which is possibly built in the handsets, is newly proposed. Low profile and small size is achieved by consisting of the half of low profile folded loop antenna, which has a structure folded loop elements sideways so that the antenna can be placed on the ground plane (GP). In the analysis, the electromagnetic simulator based on the FDTD (Finite Difference Time Domain) method is used and the design parameters useful in practical operation are found. The electromagnetic simulator based on the Method of Moment (MoM) is used to calculate the current distribution on the antenna element and the GP. An example of low profile and small size antenna which has wideband characteristics are designed based on these parameters, and the antenna characteristics such as VSWR, the current distributions and the radiation patterns are compared with Planar Inverted-F Antenna (PIFA), which is one of conventional built-in antennas for handset. As a result, it has been confirmed that the physical volume of the antenna, which has been introduced here, becomes smaller than that of PIFA. In addition, the radiation efficiency of these antennas is measured and the results are compared with each other.

Folded dipole antenna with feed line (FDAFL) whose relative bandwidth is 65% (VSWR≤3) has been reported as a wideband planar antenna for a small terminal. However, this antenna is constructed outside of the ground plane (50×80mm2) by 12mm. In this study, we analyze the antenna configurations of FDAFL in 3D so that the antenna does not protrude from the ground plane as much as possible. Two different 3D antenna models derived from FDAFL are investigated. The first model is folded over the ground plane, and the second one is folded outside of the ground plane. The relative bandwidth, the VSWR characteristics and radiation patterns are studied. As a result, it is confirmed that antenna prominence could be reduced and broadband characteristics over 74% and 83% are obtained by the 3D models, respectively, which are wider than the bandwidth of conventional 2D model. Thus, FDAFL could be used in both 2D and 3D for a small terminal.

Various planar folded dipole antennas with feed lines are introduced and analyzed. With the added feed line, the planar folded dipole antenna has two resonance modes. Moreover, adjusting the spacing and width of the feed line improves the broadband characteristics of the antenna. The attached feed line has not only an impedance transforming characteristic but also a bandwidth transforming characteristic. The bandwidth transforming characteristic means that the feed line can broaden the bandwidth of folded dipole antenna. A way to reduce the antenna area is also studied, and the characteristics of the resulting compact antenna are analyzed.

An analog-beamforming-based eigenmode transmission technique is proposed that employs a network of interconnected 180-degree hybrid couplers at both transmitting and receiving sides of a plane-symmetrically configured short-range MIMO system. This technique can orthogonalize MIMO channels regardless of array parameters such as antenna spacing and Tx-Rx distance, provided the MIMO array is symmetric. For verifying the effectiveness of the proposed technique in channel orthogonalization, an experiment is conducted using a 4×4 MIMO array consisting of microstrip antennas and cascade-connected rat-race hybrid couplers. The results indicate a reduction in interference by approximately -28.3dB on average compared to desired signal power, and the ability to realize four-stream parallel MIMO transmission by using only analog passive networks. The proposed technique can achieve channel capacity almost equivalent to that of eigenbeam space division multiplexing with ideal digital beamforming.

In order to achieve an antenna with robustness to metal for closed space wireless communications, two types of the folded monopole antenna with different input impedance have been studied. In this study, we propose the folded monopole antenna, which can switch the input impedance by a simple method. Both simulated and measured results show that the proposed antenna can improve robustness to the proximity of the metal.

As the capacity of the personal computer and workstation increase rapidly, many electromagnetic simulators are widely used. In this paper, Ansoft's High Frequency Structure Simulator (HFSS), which is a commercial software product, is applied to design a mode converter operating at 35 GHz is fabricated based on the simulation results. The numerical results are in good agreement with the measured data.

This paper presents dual bands and dual polarization reflectarrays for 5G millimeter wave applications. The frequency bands of 28GHz and 39GHz are allocated for 5G to realize high speed data transmission. However, these high frequency bands create coverage holes in which no link between base station and receivers is possible. Reflectarray has gained attention for reducing the size and number of coverage holes. This paper proposes a unit cell with swastika and the patch structure to construct the dual bands reflectrray operating at 28GHz and 39GHz by supercell. This paper also presents the detailed design procedure of the dual-bands reflectarray by supercell. The reflectarray is experimentally validated by a bistatic radar cross section measurement system. The experimental results are compared with simulation and reflection angle agreement is observed.

This study proposed a novel decoupling method for four planar inverted-F antennas (PIFAs) operating at 2.0GHz (f0). The edge-to-edge and center-to-center spacings of the adjacent PIFAs are extremely small (0.05λ0 and 0.17λ0, respectively), resulting in strong mutual coupling among them. In our previous study, we proposed a structure consisting of parasitic elements (PEs) and a bridge line (BL) for the decoupling of two PIFAs. One attractive feature of the proposed method is that no adjustment of the original structure and size of the PIFAs is necessary. However, as the number of PIFAs increases to four, their decoupling becomes considerably more complicated, and impedance mismatch is also an issue to be considered. Therefore, in this study, PEs and BLs are functionally developed to simultaneously achieve low mutual coupling and improved impedance matching of the four PIFAs. The simulated results showed that loading the proposed PEs and BLs onto the four PIFAs could reduce as well as maintain all mutual coupling for less than -10dB, and simultaneously improve impedance matching. Therefore, the total antenna efficiency at 2.0GHz could be significantly improved from 64.2% to 84.8% for PIFA1 and PIFA4, and from 35.9% to 74.2% for PIFA2 and PIFA3. Four PIFAs with PEs and BLs were fabricated and measured to validate the simulation results.

In this study, a novel decoupling method using parasitic elements (PEs) connected by a bridge line (BL) for two planar inverted-F antennas (PIFAs) is proposed. The proposed method is developed from a well-known decoupling method that uses a BL to directly connect antenna elements. When antenna elements are connected directly by a BL, strong mutual coupling can be reduced, but the resonant frequency shifts to a different frequency. Hence, to shift the resonant frequency toward the desired frequency, the original size of the antenna elements must be adjusted. This is disadvantageous if the method is applied in cases where the design conditions render it difficult to connect the antennas directly or adjust the original antenna size. Therefore, to easily reduce mutual coupling in such a case, a decoupling method that does not require both connecting antennas directly and adjusting the original antenna size is necessitated. This study demonstrates that using PEs connected by a BL reduces the mutual coupling from -6.6 to -14.1dB, and that the resonant frequency is maintained at the desired frequency (2.0GHz) without having to adjust the original PIFAs size. In addition, impedance matching can be adjusted to the desired frequency, resulting in an improved total antenna efficiency from 77.4% to 94.6%. This method is expected to be a simple and effective approach for reducing the mutual coupling between larger numbers of PIFA elements in the future.