Extremely low-voltage charge pump (ELV-CP) and its dedicated multi-stage driver (MS-DRV) for sub-60-mV thermoelectric energy harvesting are proposed. The proposed MS-DRV utilizes the output voltages of each ELV-CP to efficiently boost the control clock signals. The boosted clock signals are used as switching signals for each ELV-CP and MS-DRV to turn switch transistors on and off. Moreover, reset transistors are added to the MS-DRV to ensure an adequate non-overlapping period between switching signals. Measurement results demonstrated that the proposed MS-DRV can generate boosted clock signals of 350 mV from input voltage of 60 mV. The ELV-CP can boost the input voltage of 100 mV with 10.7% peak efficiency. The proposed ELV-CP and MS-DRV can boost the low input voltage of 56 mV.

Energy harvesting has been widely investigated as a potential solution to supply power for Internet of Things (IoT) devices. Computing devices must operate intermittently rather than continuously, because harvested energy is unstable and some of IoT applications can be periodic. Therefore, processors for IoT devices with intermittent operation must feature a hibernation mode with zero-standby-power in addition to energy-efficient normal mode. In this paper, we describe the layout design and measurement results of a nonvolatile standard cell memory (NV-SCM) and nonvolatile flip-flops (NV-FF) with a nonvolatile memory using Fishbone-in-Cage Capacitor (FiCC) suitable for IoT processors with intermittent operations. They can be fabricated in any conventional CMOS process without any additional mask. NV-SCM and NV-FF are fabricated in a 180nm CMOS process technology. The area overhead by nonvolatility of a bit cell are 74% in NV-SCM and 29% in NV-FF, respectively. We confirmed full functionality of the NV-SCM and NV-FF. The nonvolatile system using proposed NV-SCM and NV-FF can reduce the energy consumption by 24.3% compared to the volatile system when hibernation/normal operation time ratio is 500 as shown in the simulation.

In this paper, we propose a novel Hybrid-Hierarchical spatial-aerial-Terrestrial Edge-Centric (H2TEC) for the space-air integrated Internet of Things (IoT) networks. (H2TEC) comprises unmanned aerial vehicles (UAVs) that act as mobile fog nodes to provide the required services for terminal nodes (TNs) in cooperation with the satellites. TNs in (H2TEC) offload their generated tasks to the UAVs for further processing. Due to the limited energy budget of TNs, a novel task allocation protocol, named TOP, is proposed to minimize the energy consumption of TNs while guaranteeing the outage probability and network reliability for which the transmission rate of TNs is optimized. TOP also takes advantage of the energy harvesting by which the low earth orbit satellites transfer energy to the UAVs when the remaining energy of the UAVs is below a predefined threshold. To this end, the harvested power of the UAVs is optimized alongside the corresponding harvesting time so that the UAVs can improve the network throughput via processing more bits. Numerical results reveal that TOP outperforms the baseline method in critical situations that more power is required to process the task. It is also found that even in such situations, the energy harvesting mechanism provided in the TOP yields a more efficient network throughput.

A self-powered flyback pulse resonant circuit (FPRC) is proposed to extract energy from piezoelectric (PEG) and thermoelectric generators (TEG) simultaneously. The FPRC is able to cold start with the PEG voltage regardless of the TEG voltage, which means the TEG energy is extracted without additional cost. The measurements show that the FPRC can output 102 µW power under the input PEG and TEG voltages of 2.5 V and 0.5 V, respectively. The extracted power is increased by 57.6% compared to the case without TEGs. Additionally, the power improvement with respect to an ideal full-wave bridge rectifier is 2.71× with an efficiency of 53.9%.

This paper studies a harvested power-oriented simultaneous wireless information and power transfer (SWIPT) scheme over multiple-input multiple-output (MIMO) interference channels in which energy harvesting (EH) circuits exhibit nonlinearity. To maximize the power harvested by all receivers, we propose an algorithm to jointly optimize the transmit beamforming vectors, power splitting (PS) ratios and the receive decoding vectors. As all variables are coupled to some extent, the problem is non-convex and hard to solve. To deal with this non-convex problem, an iterative optimization method is proposed. When two variables are fixed, the third variable is optimized. Specifically, when the transmit beamforming vectors are optimized, the transferred objective function is the sum of several fractional functions. Non-linear sum-of-ratios programming is used to solve the transferred objective function. The convergence and advantage of our proposed scheme compared with traditional EH circuits are validated by simulation results.

In vacuum-deposited film composed of organic polar molecules, polarization charges appear on the film surface owing to spontaneous orientation of the molecule. Because its density (σpol) determines an amount of accumulation charge (σacc) in organic light-emitting diodes and output power in polar molecular-based vibrational energy generators (VEGs), control of molecular orientation is highly required. Recently, several groups have reported that dipole-dipole interaction between polar molecules induces anti-parallel orientation which does not contribute to σpol. In other words, perturbation inducing the attenuation of the dipole interaction is needed to enhance σpol. In this study, to investigate an effect of light irradiation on σpol, we prepared 1,3,5-tris(1-phenyl-1H-benzimidazol-2-yl)benzene (TPBi) film under illumination during its deposition, and evaluated the σacc in TPBi-based bilayer device, which equals to σpol. We found that the σacc was increased by light irradiation, indicating that average orientation of TPBi is enhanced. These results suggest that light irradiation during device fabrication is promising process for organic electronic devices including polar molecule-based VEGs.

A temperature-variation-tolerant intermittent startup circuit (ISC) that suppresses quiescent current to 300nA at 0.48V was developed. The ISC is a key circuit for a batteryless wireless sensor that can detect a 1μA generation current of energy harvesting sources from the intervals of wireless signals. The ISC consists of an ultralow-voltage detector composed of a depletion-type MOSFET and low-Vth MOSFETs, a Dickson-type gate-boosted charge pump circuit, and a power-switch control circuit. The detector consists of a voltage reference comparator and a feedback-controlled latch circuit for a hysteresis function. The voltage reference comparator, which has a common source stage with a folded constant-current-source load composed of a depletion-type nMOSFET, makes it possible to reduce the temperature dependency of the detection voltage, while suppressing the quiescent current to 300nA at 0.48V. The ISC fabricated with fully-depleted silicon-on-insulator (FD-SOI) CMOS technology also suppresses the variation of the quiescent current. To verify the effectiveness of the circuit, the ISC was fabricated in a 0.8-μm triple-Vth FD-SOI CMOS process. An experiment on the fabricated system, the ISC boosts the input voltage of 0.48V to 2.4V while suppressing the quiescent current to less than 300nA at 0.48V. The measured temperature coefficient of the detection voltage was ±50ppm/°C. The fluctuation of the quiescent current was 250nA ± 90nA in the temperature range from 0°C to 40°C. An intermittent energy harvesting sensor with the ISC was also fabricated. The sensor could detect a generation current of 1μA at EH sources within an accuracy of ±15% in the temperature range from 0°C to 40°C. It was also successfully applied to a self-powered wireless plant-monitoring sensor system.

In an internet of things (IoT) system using an energy harvesting device and a secondary (2nd) battery, regardless of the age of the 2nd battery, the power management shortens the lifespan of the entire system. In this paper, we propose a scheme that extends the lifetime of the energy harvesting-based IoT system equipped with a Lithium 2nd battery. The proposed scheme includes several policies of using a supercapacitor as a primary energy storage, limiting the charging level according to the predicted harvesting energy, swinging the energy level around the minimum stress state of charge (SOC) level, and delaying the charge start time. Experiments with natural solar energy measurements based on a battery aging approximation model show that the proposed method can extend the operation lifetime of an existing IoT system from less than one and a half year to more than four years.

This paper discusses and elaborates an analytical model of a multi-stage switched-capacitor (SC) voltage boost converter (VBC) for low-voltage and low-power energy harvesting systems, because the output impedance of the VBC, which is derived from the analytical model, plays an important role in the VBC's performance. In our proposed method, we focus on currents flowing into input and output terminals of each stage and model the VBCs using switching frequency f, charge transfer capacitance CF, load capacitance CL, and process dependent parasitic capacitance's parameter k. A comparison between simulated and calculated results showed that our model can estimate the output impedance of the VBC accurately. Our model is useful for comparing the relative merits of different types of multi-stage SC VBCs. Moreover, we demonstrate the performance of a prototype SC VBC and energy harvesting system using the SC VBC to show the effectiveness and feasibility of our proposed design guideline.

Radio frequency energy transfer (RET) technology has been introduced as a promising energy harvesting (EH) method to supply power in both wireless communication (WLC) and power-line communication (PLC) systems. However, current RET modified MAC (medium access control) protocols have been proposed only for WLC systems. Due to the difference in the MAC standard between WLC and PLC systems, these protocols are not suitable for PLC systems. Therefore, how to utilize RET technology to modify the MAC protocol of PLC systems (i.e., IEEE 1901), which can use the radio frequency signal to provide the transmission power and the PLC medium to finish the data transmission, i.e., realizing the ‘cooperative communication’ remains a challenge. To resolve this problem, we propose a RET modified MAC protocol for PLC systems (RET-PLC MAC). Firstly, we improve the standard PLC frame sequence by adding consultation and confirmation frames, so that the station can obtain suitable harvested energy, once it occupied the PLC medium, and the PLC system can be operated in an on-demand and self-sustainable manner. On this basis, we present the working principle of RET-PLC MAC. Then, we establish an analytical model to allow mathematical verification of RET-PLC MAC. A 2-dimension discrete Markov chain model is employed to derive the numerical analysis results of RET-PLC MAC. The impacts of buffer size, traffic rate, deferral counter process of 1901, heterogeneous environment and quality of information (QoI) are comprehensively considered in the modeling process. Moreover, we deduce the optimal results of system throughput and expected QoI. Through extensive simulations, we show the performance of RET-PLC MAC under different system parameters, and verify the corresponding analytical model. Our work provides insights into realizing cooperative communication at PLC's MAC layer.

In this paper, we propose a filter-and-forward relay scheme with energy harvesting for single-carrier transmission in frequency-selective channels. The relay node harvests energy from both the source node transmit signal and its own transmit signal by self-energy recycling. The signal received by the relay node is filtered to suppress the inter-symbol interference and then forwarded to the destination node using the harvested energy. We consider a filter design method based on the signal-to-interference-plus-noise power ratio maximization, subject to a constraint that limits the relay transmit power. In addition, we provide a golden-section search based algorithm to optimize the power splitting ratio of the power splitting protocol. The simulation results show that filtering and self-energy recycling of the proposed scheme are effective in improving performance. It is also shown that the proposed scheme is useful even when only partial channel state information is available.

A triple-band CP rectenna for ambient RF energy harvesting is presented in this paper. A simple broadband CP slot antenna has been proposed with the bandwidth of 51.1% operating from 1.53 to 2.58GHz, which can cover GSM-1800, UMTS-2100 and 2.45GHz WLAN bands. Accordingly, a triple-band rectifying circuit is designed to convert RF energy in the above bands, with the maximum RF-DC conversion efficiency of 42.5% at a relatively low input power of -5dBm. Additionally, the rectenna achieves the maximum conversion efficiency of 12.7% in the laboratory measurements. The measured results show a good performance in the laboratory measurements.

This paper investigates the secrecy energy efficiency maximization (SEEM) problem in a simultaneous wireless information and power transfer (SWIPT) system, wherein a legitimate user (LU) exploits the power splitting (PS) scheme for simultaneous information decoding (ID) and energy harvesting (EH). To prevent interference from eavesdroppers on the LU, artificial noise (AN) is incorporated into the confidential signal at the transmitter. We maximize the secrecy energy efficiency (SEE) by joining the power of the confidential signal, the AN power, and the PS ratio, while taking into account the minimum secrecy rate requirement of the LU, the required minimum harvested energy, the allowed maximum radio frequency transmission power, and the PS ratio. The formulated SEEM problem involves nonconvex fractional programming and is generally intractable. Our solution is Lagrangian relaxation method than can transform the original problem into a two-layer optimization problem. The outer layer problem is a single variable optimization problem with a Lagrange multiplier, which can be solved easily. Meanwhile, the inner layer one is fractional programming, which can be transformed into a subtractive form solved using the Dinkelbach method. A closed-form solution is derived for the power of the confidential signal. Simulation results verify the efficiency of the proposed SEEM algorithm and prove that AN-aided design is an effective method for improving system SEE.

In this work, we investigate a joint transmit beamforming and artificial noise (AN) covariance matrix design in a multiple-input multiple-output (MIMO) cognitive radio (CR) downlink network with simultaneous wireless information and power transfer (SWIPT), where the malicious energy receivers (ERs) may decode the desired information and hence can be treated as potential eavesdroppers (Eves). In order to improve the secure performance of the transmission, AN is embedded to the information-bearing signal, which acts as interference to the Eves and provides energy to all receivers. Specifically, this joint design is studied under a practical non-linear energy harvesting (EH) model, our aim is to maximize the secrecy rate at the SR subject to the transmit power budget, EH constraints and quality of service (QoS) requirement. The original problem is not convex and challenging to be solved. To circumvent its intractability, an equivalent reformulation of this secrecy rate maximization (SRM) problem is introduced, wherein the resulting problem is primal decomposable and thus can be handled by alternately solving two convex subproblems. Finally, numerical results are presented to verify the effectiveness of our proposed scheme.

This paper introduces an energy-efficient transmit design for multiple-input single-output (MISO) energy-harvesting cognitive radio (CR) networks in the presence of external eavesdroppers (Eves). Due to the inherent characteristics of CR network with simultaneous wireless information and power transfer (SWIPT), Eves may illegitimately access the primary user (PU) bands, and the confidential message is prone to be intercepted in wireless communications. Assuming the channel state information (CSI) of the Eves is not perfectly known at the transmitter, our approach to guaranteeing secrecy is to maximize the secrecy energy efficiency (SEE) by jointly designing the robust beamforming and the power splitting (PS) ratio, under the constraints of total transmit power, harvested energy at secondary receiver (SR) and quality of service (QoS) requirement. Specifically, a non-linear energy harvesting (EH) model is adopted for the SR, which can accurately characterize the property of practical RF-EH circuits. To solve the formulated non-convex problem, we first employ fractional programming theory and penalty function to recast it as an easy-to-handle parametric problem, and then deal with the non-convexity by applying S-Procedure and constrained concave convex procedure (CCCP), which enables us to exploit the difference of concave functions (DC) programming to seek the maximum worst-case SEE. Finally, numerical results are presented to verify the performance of the proposed scheme.

This paper looks into the underlying RF energy harvesting issues at low input ambient power levels below 0 dBm where efficiency degradation is severe. The proposed design aims to improve the rectenna sensitivity, efficiency, and output DC power. In the same manner, we are using a straightforward and compact size rectenna design. The receiving antenna is a coplanar waveguide (CPW) slot monopole antenna with harmonic suppression property and a peak measured gain of 3 dBi. Also, an improved antenna radiation characteristics, e.g radiation pattern and gain covering the desired operating band (ISM 2.45 GHz), is observed. The rectifier is a voltage doubler circuit based on microstrip (MS) structure. Two architectures of rectenna were carefully designed, fabricated and tested. The first layout; antenna, and rectifier were fabricated separately and then connected using a connector. The peak efficiency (40% at -5 dBm) achieved is lower than expected. To improve the efficiency, a high compactness and simple integration between antenna and rectifier are achieved by using a smooth CPW-MS transition. This design shows improved conversion efficiency measurement results which typically agree with the simulation results. The measured peak conversion efficiency is 72% at RF power level of -7 dBm and a load resistance of 2 kΩ.

This paper studies the secrecy throughput performance of the three-node wireless-powered networks and proposes two secure transmission schemes, namely the half-duplex maximal ratio combining (HD&MRC) scheme and the full-duplex jamming scheme based on time switching simultaneous wireless information and power transfer (FDJ&TS-SWIPT). The closed-form expressions of the secrecy throughput are derived, and intuitive comparison of the two schemes is provided. It is illustrated that the HD&MRC scheme only applies to the low and medium signal-to-noise ratio (SNR) regime. On the contrary, the suitable SNR regime of the FDJ&TS-SWIPT is much wider. It is depicted that FDJ&TS-SWIPT combing with current passive self-interference cancellation (SIC) algorithm outperforms HD&MRC significantly, especially when a medium or high transmit SNR is provided. Numerical simulations are conducted for verifying the validity of the analysis.

In this letter, we consider a multiple-input multiple-output (MIMO) simultaneous wireless information and power transfer (SWIPT) system, in which the confidential message intended for the information receiver (IR) should be kept secret from the energy receiver (ER). Our goal is to design the optimal transmit covariance matrix so as to maximize the secrecy energy efficiency (SEE) of the system while guaranteeing the secrecy rate, energy harvesting and transmit power constraints. To deal with the original non-convex optimization problem, we propose an alternating optimization (AO)- based algorithm and also prove its convergence. Simulation results show that the proposed algorithm outperforms conventional design methods in terms of SEE.

A penta-band antenna based on the mu-negative transmission line is presented for radio frequency (RF) energy harvesting application. The antenna utilizes five radiation modes; two quarter wavelength resonances, three quarter wavelength resonance, zeroth order resonance, and first order resonance. The parasitic radiating strip antenna generates quarter wavelength resonance radiation. The dual band antenna based on two unit cell mu-negative (MNG) transmission line gives birth to the zeroth order resonance (ZOR) mode and the first order resonance (FOR) mode. The parasitic radiating strip and dual band antenna based on two unit mu-negative (MNG) transmission line are magnetically coupled by a feed monopole with gap. This feed monopole, simultaneously, radiates at quarter and three quarter wavelength resonance frequency to cover the other bands. The multi-mode coupling mechanism of this penta-band antenna is well modeled by our derived equivalent circuit. The measured radiation efficiencies are more than 87% over the entire penta-band.

In this paper, we study simultaneous wireless information and power transfer (SWIPT) in two-way relay channels where two users exchange information with each other via a multi-antenna relay node. The signals forwarded by the relay node are also used to supply the power to two users. We formulate a max-min optimization problem aiming to maximize the minimum harvested energy between two users to achieve fairness. We jointly optimize the relay beamforming matrix and allocating powers at the two users subject to the quality of service (QoS) constraints. To be specific, we consider the amplify-and-forward (AF) relay strategy and the time splitting SWIPT strategy. To this end, we propose two different time splitting protocols to enable relay to supply power to two users. To solve the non-convex joint optimization problem, we propose to split the original optimization problem into two subproblems and solving them iteratively to obtain the final solution. It is shown that the first subproblem dealing with the beamforming matrix can be optimally solved by using the technique of relaxed semidefinite programming (SDR), and the second subproblem, which deals with the power allocation, can be solved via linear programming. The performance comparison of two schemes as well as the one-way relaying scheme are provided and the effectiveness of the proposed schemes is verified.