In this paper, a precise design method of high-order bandpass filters (BPFs) with complicated coupling topologies is proposed, and is demonstrated through the design of an 11-pole BPF using TM010 mode dielectric resonators (DRs). A novel Z-shaped coupling structure is proposed which avoids the mixed use of TM010 and TM01δ modes and enables the tuning and assembling of the filter much easier. The coupling topology of the BPF includes three cascade triplets (CTs) of DRs, and both the capacitive and inductive couplings in the CTs are designed independently tunable, which produce consequently three controllable transmission zeros on both sides of the passband of filter. A procedure of mapping the coupling matrix of BPF to its physical dimensions is developed, and an iterative optimization of these physical dimensions is implemented to achieve best performance. The design of the 11-pole BPF is shown highly precise by the excellent agreement between the electromagnetic simulated response of the filter and the desired target specifications.

We achieved 10-Gbit/s data transmission using a cutting-edge 120-GHz-band high-speed contactless communication technology, which allows seamless connection to a local area network (LAN) by simply placing devices on a desk. We propose a glass substrate-integrated rectangular waveguide that can control the permeability of the top surface to 120-GHz signals by contacting a dielectric substrate with the substrate. The top surface of the rectangular waveguide was replaced with a glass substrate on which split-ring resonators (SRRs) were integrated. The transmission loss of the waveguide with a glass substrate was 2.5 dB at 125 GHz. When a dielectric sheet with a line pattern formed on the contact surface was in contact with a glass substrate, the transmission loss from the waveguide to the dielectric sheet was 19.2 dB at 125 GHz. We achieved 10-Gbit/s data transmission by contacting a dielectric sheet to the SRR-integrated glass substrate.

For 6G mobile communications, it is important to realize a 300 GHz band bandpass filter that fits the occupied bandwidth of wireless communication system to prevent inter-system interference. This paper presents the design of a 300-GHz-band dual-band bandstop filter composed of two types of different sized split ring resonator (SRR) unit cells. The SRR unit cells are formed by a 5-μm-thick gold pattern on a 200-μm-thick quartz substrate. When two different-sized SRR unit cells are placed alternately on the same quartz substrate and the SRR unit cell size is over 260 μm, the stopbands of the dual-band bandstop filter are almost the same as those of the bandstop filter, which is composed of a single SRR unit cell. The insertion loss of the dual-band bandstop filter at 297.4 GHz is 1.8 dB and the 3-dB passband becomes 16.0 GHz (290.4-306.4 GHz). The attenuation in the two stopbands is greater than 20 dB. Six types of dual-band bandstop filters with different arrangement and different distance between SRR unit cells are prototyped, and the effect of the distance and arrangement between different sized SRR unit cells on the transmission characteristics of dual-band bandstop filters were clarified.

This paper proposes a dual-polarized filtering antenna with extracted-pole unit (EPU) using LTCC substrate. The EPU realizes the high skirt characteristic of the bandpass filter with transmission zeros (TZs) located near the passband without cross coupling. The filtering antenna with EPU is designed and fabricated in 28GHz band for 5G Band-n257 (26.5-29.5GHz). The measured S11 is less than -10.6dB in Band-n257, and the isolation between two ports for dual polarization is greater than 20.0dB. The measured peak antenna gain is 4.0dBi at 28.8GHz and the gain is larger than 2.5dBi in Band-n257. The frequency characteristics of the measured antenna gain shows the high skirt characteristic out of band, which are in good agreement with electromagnetic (EM)-simulated results.

In this paper, we applied the circuit synthesis theory of filters to the design of transmission-type metasurface cells and arbitrarily designed the amplitude and phase of the transmission and reflection by adjusting the resonant frequency and coupling coefficient. In addition, we successfully designed the phase of the unit cell by using the frequency conversion of filter theory. Moreover, we designed a refractive transmission-type metasurface plate with a novel cell structure that reacts to both polarizations. The prototype operated at the desired refraction angle, confirming the design theory.

Bandpass filters (BPFs) are very important to extract target signals and eliminate noise from the received signals. A BPF of which frequency characteristics is a sum of Gaussian functions is called the Gaussian mixture BPF (GMBPF). In this research, we propose to implement the GMBPF approximately by the sum of several frequency components of the sliding Fourier transform (SFT) or the attenuated SFT (ASFT). Because a component of the SFT/ASFT can be approximately realized using the finite impulse response (FIR) recursive filters, its calculation complexity does not depend on the length of the impulse response. The property makes GMBPF ideal for narrow bandpass filtering applications. We conducted experiments to demonstrate the advantages of the proposed GMBPF over FIR filters designed by a MATLAB function with regard to the computational complexity.

A novel compact 5-pole bandpass filter (BPF) using two different types of resonators, one is coaxial TEM-mode resonator and the other dielectric triple-mode resonator, is proposed in this paper. The coaxial resonator is a simple single-mode resonator, while the triple-mode dielectric resonator (DR) includes one TM01δ mode and two degenerate HE11 modes. An excellent spurious performance of the BPF is obtained due to the different resonant behaviors of these two types of resonators used in the BPF. The coupling scheme of the 5-pole BPF includes two cascade triplets (CTs) which produce two transmission zeros (TZs) and a sharp skirt of the passband. Behaviors of the resonances, the inter-resonance couplings, as well as their tuning methods are investigated in detail. A procedure of mapping the coupling matrix of the BPF to its physical dimensions is developed, and an optimization of these physical dimensions is implemented to achieve best performance of the filter. The designed BPF is operated at 1.84GHz with a bandwidth of 51MHz. The stopband rejection is better than 20dB up to 9.7GHz (about 5.39×f0) except 7.85GHz. Good agreement between the designed and theoretically synthesized responses of the BPF is reached, verifying well the proposed configuration of the BPF and its design method.

Realizing frequency rectangular characteristics using a planar circuit made of a normal conductor material such as a printed circuit board (PCB) is difficult. The reason is that the corners of the frequency response are rounded by the effect of the low unloaded quality factors of the resonators. Rectangular frequency characteristics are generally realized by a low-noise amplifier (LNA) with flat gain characteristics and a high-order bandpass filter (BPF) with resonators having high unloaded quality factors. Here, we use an LNA and a fourth-order flat passband BPF made of a PCB to realize the desired characteristics. We first calculate the signal and noise powers to confirm any effects from insertion loss caused by the BPF. Next, we explain the design and fabrication of an LNA, since no proper LNAs have been developed for this research. Finally, the rectangular frequency characteristics are shown by a circuit combining the fabricated LNA and the fabricated flat passband BPF. We show that rectangular frequency characteristics can be realized using a flat passband BPF technique.

For the blind estimation of short-code direct sequence spread spectrum (DSSS) signal pseudo-noise (PN) sequences, the eigenvalue decomposition (EVD) algorithm, the singular value decomposition (SVD) algorithm and the double-periodic projection approximation subspace tracking with deflation (DPASTd) algorithm are often used to estimate the PN sequence. However, when the asynchronous time delay is unknown, the largest eigenvalue and the second largest eigenvalue may be very close, resulting in the estimated largest eigenvector being any non-zero linear combination of the really required largest eigenvector and the really required second largest eigenvector. In other words, the estimated largest eigenvector exhibits unitary ambiguity. This degrades the performance of any algorithm estimating the PN sequence from the estimated largest eigenvector. To tackle this problem, this paper proposes a spreading sequence blind estimation algorithm based on the rotation matrix. First of all, the received signal is divided into two-information-period-length temporal vectors overlapped by one-information-period. The SVD or DPASTd algorithm can then be applied to obtain the largest eigenvector and the second largest eigenvector. The matrix composed of the largest eigenvector and the second largest eigenvector can be rotated by the rotation matrix to eliminate any unitary ambiguity. In this way, the best estimation of the PN sequence can be obtained. Simulation results show that the proposed algorithm not only solves the problem of estimating the PN sequence when the largest eigenvalue and the second largest eigenvalue are close, but also performs well at low signal-to-noise ratio (SNR) values.

This paper presents a 6th-order quadrature bandpass delta sigma AD modulator (QBPDSM) with 2nd-order image rejection using dynamic amplifier and noise coupling (NC) SAR quantizer embedded by passive adder for the application of wireless communication system. A novel complex integrator using dynamic amplifier is proposed to improve the energy efficiency of the QBPDSM. The NC SAR quantizer can realize an additional 2nd-order noise shaping and 2nd-order image rejection by the digital domain noise coupling technique. As a result, the 6th-order QBPDSM with 2nd-order image rejection is realized by two complex integrators using dynamic amplifier and the NC SAR quantizer. The SPICE simulation results demonstrate the feasibility of the proposed QBPDSM in 90nm CMOS technology. Simulated SNDR of 76.30dB is realized while a sinusoid -3.25dBFS input is sampled at 33.3MS/s and the bandwidth of 2.083MHz (OSR=8) is achieved. The total power consumption in the modulator is 6.74mW while the supply voltage is 1.2V.

The 1-bit digital radio frequency (DRF) transmitter using a band-pass delta-sigma modulator (BP-DSM) can output a radio frequency (RF) signal carrying a binary data stream with a constant data rate regardless of the carrier frequency, which makes it possible to transmit RF signals over digital optical links with a constant bit rate. However, the optical link requires a line coding, such as 8B10B or 64B66B, to constrain runlength and disparity, and the line coding corrupts the DRF power spectrum owing to additional or encoded data. This paper proposes a new line coding for BP-DSM, which is able to control the runlength and the disparity of the 1-bit data stream by adding a notch filter to the BP-DSM that suppresses the low frequency components. The notch filter stimulates the data change and balances the direct current (DC) components. It is demonstrated that the proposed line coding shortens the runlength from 50 bits to less than 8 bits and reduces the disparity from several thousand bits to 5 bits when the 1-bit DRF transmitter outputs an LTE signal with 5 MHz bandwidth, when using carrier frequencies from 0.5GHz to 2GHz and an output power variation of 60dB.

We have developed the high speed bandpass liquid crystal filter with narrow full width at half maximum (FWHM) of 5nm for real-time multi spectral imaging systems. We have successfully achieved short wavelength-switching time of 30ms by the optimization of phase retardation of thin liquid crystal cells.

For more flexible and efficient use of radio spectrum, reconfigurable RF devices have important roles in the future wireless systems. In 5G mobile communications, concurrent multi-band operation using new SHF bands is considered. This paper presents a new configuration of dual-band SHF BPF consisting of a low SHF three-bit reconfigurable BPF and a high SHF BPF. The proposed dual-band BPF employs direct parallel connection without additional divider/combiner to reduce circuit elements and simplify the BPF. In order to obtain a good isolation between two passbands while achieving a wide center frequency range in the low SHF BPF, input/output impedances and external Qs of BPFs are analyzed and feedbacked to the design. A high SHF BPF design method with tapped transmission line resonators and lumped-element coupling is also presented to make the BPF compact. Two types of prototypes; all inductor-coupled dual-band BPF and C-L-C coupled dual-band BPF were designed and fabricated. Both prototypes have low SHF reconfigurable center frequency range from 3.5 to 5 GHz as well as high SHF center frequency of 8.5 GHz with insertion loss below 2.0 dB.

This paper presents a theoretical design of novel THz bandpass filters composed of M-PhC (metallic-photonic-crystal) point-defect-cavities (PDCs) with a centrally-loaded-rod. After a brief review of the properties of the recently-proposed M-PhC PDCs, two inline-type bandpass filters are synthesized in terms of the coupling matrix theory. The FDTD simulation results of the synthesized filters are in good agreement with the theoretical ones, which confirms the validity of the proposed filters' structures and the design scheme.

The 1-bit band-pass delta-sigma modulator (BP-DSM) achieves high resolution if it uses an oversampling technique. This method can generate concurrent dual-band RF signals from a digitally modulated signal using a 1-bit digital pulse train. It was previously reported that the adjacent channel leakage ratio (ACLR) deteriorates owing to the asymmetrical waveform created by the pulse transition mismatch error of the rising and falling waveforms in the time domain and that the ACLR can be improved by distortion compensation. However, the reported distortion compensation method can only be performed for single-band transmission, and it fails to support multi-band transmission because the asymmetrical waveform compensated signal extends over a wide frequency range and is itself a harmful distortion outside the target band. Unfortunately, the increase of out-of-band power causes the BP-DSM unstable. We therefore propose a distortion compensator for a concurrent dual-band 1-bit BP-DSM that consists of a noise transfer function with a quasi-elliptic filter that can control the out-of-band gain frequency response against out-of-band oscillation. We demonstrate that dual-band LTE signals, each with 40MHz (2×20MHz) bandwidth, at 1.5 and 3.0GHz, can be compensated concurrently for spurious distortion under various combinations of rising and falling times and ACLR of up to 48dB, each with 120MHz bandwidth, including the double sided adjacent channels and next adjacent channels, is achieved.

We present a design approach and analysis of a multimode stripline resonator (MSR). Furthermore, a bandpass filter (BPF) using a single MSR is presented. MSR has three fundamental modes, incorporating two transmission resonance modes and one quasi-lumped component (LC) resonance mode. The resonant frequencies and unloaded Q factors of those modes are theoretically derived by transmission modes and LC modes. By our equations, it is also explained that the resonant frequencies can be shown to be easily handled by an increase and decrease in the number of via holes. These frequencies calculated by our equations are in good agreement with those of 3-D simulations and measurements. Finally, design approach of a narrow bandpass filter using our resonator is introduced. Good agreement between measured and computed result is obtained.

This paper describes the broadband radio access techniques for Universal Mobile Terrestrial Systems (UMTS)/Wideband Code Division Multiple Access (W-CDMA), High-Speed Downlink Packet Access (HSDPA)/High-Speed Uplink Packet Access (HSUPA), Long Term Evolution (LTE), and LTE-Advanced. Major technical pillars are almost identical regardless of the radio access systems of the respective generations. However, the key techniques that provide distinct performance improvements have changed according to the system requirements in each generation. Hence, in this paper, we focus on the key techniques associated with the system requirements. We also describe the requirements, radio access technology candidates, and challenges toward the future 5G systems.

We propose an architecture for a 1-bit band-pass delta-sigma modulator (BP-DSM) that outputs concurrent multiband RF signals. The proposed BP-DSM consists of parallel bandpass filters (BPFs) in the feedback loop to suppress the quantization noise at each target frequency band while maintaining the stability. Each BPF is based on second-order parallel infinite impulse response (IIR) filters. This architecture can unify and reconfigure the split BPFs according to the number of bands. The architecture complexity is proportional to the bandwidth of each RF signal and is independent of the carrier spacing between the bands. The conventional architecture of a concurrent multiband digital modulator, reported previously, has multiple input ports to the dedicated BPF at each band and so it cannot be efficiently integrated. Measurements show that the proposed architecture is feasible for transmitting a concurrent dual-band and a triple-band by changing the 1-bit digital data stream while keeping a data transmission rate of 10Gb/s. We demonstrate that the proposed architecture outputs the signal with LTE intra-band and inter-band carrier aggregation on 0.8GHz, 2.1GHz and 3.5GHz, each with 40MHz bandwidth in 120MHz aggregated bandwidth, whose bandwidth surpasses the bandwidth with carrier aggregation of LTE-A up to 100MHz. Adjacent channel leakage ratios of -49dBc and -46dBc are achieved at 3.5GHz in the concurrent dual-band and triple-band, respectively.

The 1-bit band-pass delta-sigma modulator (BP-DSM) achieves high resolution by using the oversampling technique. This method allows direct RF signal transmission from a digitally modulated signal, using a 1-bit digital pulse train. However, it has been previously reported that the adjacent channel leakage ratio (ACLR) in a target frequency band degrades due to the pulse transition mismatch between rising and falling waveforms in the time domain. This paper clarifies that the spurious distortion in BP-DSM is caused by the asymmetricity of the waveform about the center of an eye pattern in the time axis, and proposes a 1-bit BP-DSM with the compensator consisting of a fractional delay filter and a binary data differentiator to cancel out the asymmetry in the target frequency band. This can accurately provide a wideband cancellation signal with more than 100MHz bandwidth, including the adjacent channel, within 50dB power dynamic range. Using long term evolution (LTE) signals with 5MHz bandwidth at 0.8GHz, we simulated the spurious distortion, performing various combinations of rising and falling times in the eye pattern, and the proposed 1-bit BP-DSM always achieved high ACLR, up to 60dB, in 140MHz bandwidth, under all conditions.

Design of lumped-element immittance inverters which support dual-frequency operation and tuning of both operational frequencies is presented. Unique properties of the dual-composite right/left-handed transmission lines (D-CRLH TL) give an opportunity to design immittance inverters with two non-multiple operational frequencies and a stop band between them. Replacement of capacitors of D-CRLH TL unit cells with variable ones enables inverter tunability. Tunability analysis of such immittance inverters is given. It is shown that a tuning range of the operational frequencies is limited by a tolerable variation of the inverter parameter. The design concept is verified by results of electromagnetic simulation and measured frequency characteristics of fixed (non-tunable) as well as tunable dual-frequency immittance inverters and dual-band filters using the inverters.