The combination of peak-to-average power ratio (PAPR) reduction and predistortion (PD) techniques effectively reduces the nonlinear distortion of a transmission signal caused by power amplification and improves power efficiency. In this paper, assuming downlink amplify-and-forward (AF)-type relaying of multiple-input multiple-output (MIMO)-orthogonal frequency division multiplexing (OFDM) signals, we propose a joint method that combines a PD technique with our previously reported PAPR reduction method utilizing the null space of a MIMO channel. In the proposed method, the reported PAPR reduction method reduces the PAPR at a relay station (RS) as well as that at a base station (BS) by using only signal processing at the BS. The PD process at the BS and RS further reduces the nonlinear distortion caused by nonlinear power amplification. Computer simulation results show that the proposed method enhances the effectiveness of PD at the BS and RS and achieves further coverage enhancement compared to conventional methods.

In a 100VDC/5A resistive circuit, silver electrical contacts with airflow ejection structure are separated at a constant speed. Break arcs are generated between the contacts and blown by the airflow between the contact gap. Airflow rate is varied by changing shapes of the contacts. The break arcs are observed by two high-speed cameras. Following results are shown. Arc duration is shortened by the airflow. When the airflow rate is increased, the arc duration becomes shorter, and the break arcs are driven farther outward from the center axis of the contacts and are extinguished in a shorter length.

Electrical contacts are separated at a constant opening speed in a 48VDC/50A-600A resistive circuit. Break arcs are observed using two high-speed cameras from the top and side directions. Lengths of the break arcs are analyzed from images taken by the cameras. Arc voltages and currents corresponding to the analyzed arc lengths are investigated to obtain voltage-current characteristics of the break arcs. Relationships between the arc length versus gap voltage and the arc length versus circuit current are obtained. These results are slightly scattered. Therefore, to obtain one-to-one relationships between the arc length and the gap voltage, approximate curves should be determined for these results. Using these approximate curves, eventually, the voltage-current characteristics for each arc length are indicated.

In this paper, we investigate a wireless-powered relays assisted batteryless IoT network based on the non-linear energy harvesting model, where there exists an energy service provider constituted by the hybrid access point (HAP) and an IoT service provider constituted by multiple clusters. The HAP provides energy signals to the batteryless devices for information backscattering and the wireless-powered relays for energy harvesting. The relays are deployed to assist the batteryless devices with the information transmission to the HAP by using the harvested energy. To model the energy interactions between the energy service provider and IoT service provider, we propose a Stackelberg game based framework. We aim to maximize the respective utility values of the two providers. Since the utility maximization problem of the IoT service provider is non-convex, we employ the fractional programming theory and propose a block coordinate descent (BCD) based algorithm with successive convex approximation (SCA) and semi-definite relaxation (SDR) techniques to solve it. Numerical simulation results confirm that compared to the benchmark schemes, our proposed scheme can achieve larger utility values for both the energy service provider and IoT service provider.

The transfer distance of the wireless power transfer (WPT) system with relay coil is longer, so this technology have a better practical perspective. But the location of the relay coil has a great impact on the transmission efficiency of the WPT system, and it is not easy to analyze. In order to research the influence law of the relay coil location on the transmission efficiency and obtain the optimal location, the paper firstly proposes the concept of relay coil location factor. And based on the location factor, a novel method for studying the influence of the relay coil location on the transmission efficiency is proposed. First, the mathematical model between the transmission efficiency and the location factor is built. Next, considering the transfer distance, coil radius, coil turns and load resistance, a lot of simulations are carried out to analyze the influence of the location factor on the transmission efficiency, respectively. The influence law and the optimal location factor were obtained with different parameters. Finally, a WPT system with relay coil was built for experiments. And the experiment results verify that the theoretical analysis is correct and the proposed method can simplify the analysis progress of the influence of relay coil location on the transmission efficiency. Moreover, the proposed method and the research conclusions can provide guidance for designing the multiple coils structure WPT system.

In this paper, we investigate the sum rate (SR) maximization problem for downlink cooperative non-orthogonal multiple access (C-NOMA) system under in-phase and quadrature-phase (IQ) imbalance at the base station (BS) and destination. The BS communicates with users by a half-duplex amplified-and-forward (HD-AF) relay under imperfect IQ imbalance. The sum rate maximization problem is formulated as a non-convex optimization with the quality of service (QoS) constraint for each user. We first use the variable substitution method to transform the non-convex SR maximization problem into an equivalent problem. Then, a joint power and rate allocation algorithm is proposed based on successive convex approximation (SCA) to maximize the SR of the systems. Simulation results verify that the algorithm can improve the SR of the C-NOMA compared with the cooperative orthogonal multiple access (C-OMA) scheme.

This paper proposes a scheme that reduces residual self-interference significantly in the analog-circuit domain on wireless full-duplex relay systems. Full-duplex relay systems utilize the same time and frequency resources for transmission and reception at the relay node to improve spectral efficiency. Our proposed scheme measures multiple responses of the feedback path by changing the direction of the main beam of the transmitter at the relay, and then selecting the optimal direction that minimizes the residual self-interference. Analytical residual self-interference is derived as the criterion to select the optimal direction. In addition, this paper considers the target of residual self-interference power before the analog-to-digital converter (ADC) dependent on the dynamic range in the analog-circuit domain. Analytical probability that the residual interference exceeds the target is derived to help in determining the number of measured responses of the feedback path. Computer simulations validate the analytical results, and show that in particular, the proposed scheme with ten candidates improves the residual self-interference by approximately 6dB at the probability of 0.01 that the residual self-interference exceeds target power compared with a conventional scheme with the feedback path modeled as Rayleigh fading.

In this letter, we propose an energy beamforming empowered relaying scheme for a batteryless IoT network, where wireless-powered relays are deployed between the hybrid access point (HAP) and batteryless IoT devices to assist the uplink information transmission from the devices to the HAP. In particular, the HAP first exploits energy beamforming to efficiently transmit radio frequency (RF) signals to transfer energy to the relays and as the incident signals to enable the information backscattering of batteryless IoT devices. Then, each relay uses the harvested energy to forward the decoded signals from its corresponding batteryless IoT device to the HAP, where the maximum-ratio combing is used for further performance improvement. To maximize the network sum-rate, the joint optimization of energy beamforming vectors at the HAP, network time scheduling, power allocation at the relays, and relection coefficient at the users is investigated. As the formulated problem is non-convex, we propose an alternating optimization algorithm with the variable substitution and semi-definite relaxation (SDR) techniques to solve it efficiently. Specifically, we prove that the obtained energy beamforming matrices are always rank-one. Numerical results show that compared to the benchmark schemes, the proposed scheme can achieve a significant sum-rate gain.

In time difference of arrival-based signal source location estimation, geometrical errors are caused by the location of multiple unmanned aerial vehicles (UAV). Herein, we propose a divide-and-conquer algorithm to determine the optimal location for each UAV. Simulations results confirm that multiple UAVs shifted to an optimal position and the location accuracy improved.

Device-to-device (D2D) relay enhances the capacity of a mobile network. If the channel quality of a user equipment (UE) is bad, the UE asks a neighbor to get its data from the base station and forward the data to it by using D2D communication. Since cellular and D2D communication can share spectrum resources, the spectral efficiency will rise. As UEs are owned by self-interested users, they may not provide relay services gratis. Thus, some incentive methods let UEs exchange tokens to buy and sell relay services. However, they assume that each relay service is worth one token and offers a fixed data rate, which lacks flexibility. Through the law of supply and demand, this paper proposes an economy aware token-based incentive (EAT-BI) strategy. A supplier (i.e., the service provider) charges different prices for its relay service with different rates. A consumer (i.e., the service requestor) takes different policies to choose a supplier based on its tokens and may bargain with suppliers to avoid starvation. Simulation results show that EAT-BI can efficiently promote D2D relay use and increase throughput under different mobility models of UEs.

In this paper, we propose applying our previously reported adaptive peak-to-average power ratio (PAPR) reduction method using null space in a multiple-input multiple-output (MIMO) channel for orthogonal frequency division multiplexing (OFDM) signals to the downlink MIMO amplify-and-forward (AF) relaying transmission. Assuming MIMO-OFDM transmission, mitigating its high PAPR not only at the base station (BS) but also at the relay station (RS) transmitters is essential to achieve sufficient coverage enhancement from the RSs by minimizing the transmission power backoff levels at the nonlinear power amplifier. In this study, we assume an AF-type RS with multiple antennas. In the proposed method, the BS suppresses the PAPR of the transmitted signal through adaptive PAPR reduction utilizing the null space of the integrated overall MIMO channel that combines the channel between the BS and RS and the channel between the RS and a set of user equipment (UE). However, the PAPR of the received signal at each RS antenna is increased again due to the MIMO channel between the BS and RS. The proposed method reduces this increased PAPR at the AF-type RS transmitter by PAPR reduction processing that utilizes the null space in the MIMO channel between the RS and UE. Since the in-band PAPR reduction signal added at the RS transmitter is transmitted only in the null space of the MIMO channel between the RS and UE, interference at the UE receiver is mitigated. Computer simulation results show that the proposed method significantly improves the PAPR-vs.-throughput performance compared to that for the conventional one thanks to the reduced interference levels from the PAPR reduction signal observed at the UE receiver.

In this paper, to improve communication system's energy-efficiency (EE), multi-case optimization of two new transmission strategies is investigated. Firstly, with amplify-and-forward relaying and full-duplex technique, two new transmission strategies are designed. The designed transmission strategies consider direct links and non-ideal transmission conditions. At the same time, detailed capacity and energy consumption analyses of the designed transmission strategies are given. In addition, EE optimization and analysis of the designed transmission strategies are studied. It is the first case of EE optimization and it is achieved by joint optimization of transmit time (TT) and transmit power (TP). Furthermore, the second and third cases of EE optimization with respectively optimizing TT and TP are given. Simulations reveal that the designed transmission strategies can effectively improve the communication system's EE.

In this paper, we explore the physical layer security of an Internet of Things (IoT) network comprised of multiple relay-user pairs in the presence of multiple malicious eavesdroppers and channel estimation error (CEE). In order to guarantee secure transmission with channel estimation error, we propose a channel estimation error oriented joint relay-user pair and friendly jammer selection (CEE-JRUPaFJS) scheme to improve the physical layer security of IoT networks. For the purpose of comparison, the channel estimation error oriented traditional round-robin (CEE-TRR) scheme and the channel estimation error oriented traditional pure relay-user pair selection (CEE-TPRUPS) scheme are considered as benchmark schemes. The exact closed-form expressions of outage probability (OP) and intercept probability (IP) for the CEE-TRR and CEE-TPRUPS schemes as well as the CEE-JRUPaFJS scheme are derived over Rayleigh fading channels, which are employed to characterize network reliability and security, respectively. Moreover, the security-reliability tradeoff (SRT) is analyzed as a metric to evaluate the tradeoff performance of CEE-JRUPaFJS scheme. It is verified that the proposed CEE-JRUPaFJS scheme is superior to both the CEE-TRR and CEE-TPRUPS schemes in terms of SRT, which demonstrates our proposed CEE-JRUPaFJS scheme are capable of improving the security and reliability performance of IoT networks in the face of multiple eavesdroppers. Moreover, as the number of relay-user pairs increases, CEE-TPRUPS and CEE-JRUPaFJS schemes offer significant increases in SRT. Conversely, with an increasing number of eavesdroppers, the SRT of all these three schemes become worse.

In this paper, in order to avoid the cascading failure by increasing the number of links in the physical network in D2D-based SNS, we propose an autonomous device placement algorithm. In this method, some relay devices are placed so as to increase the number of links in the physical network. Here, relay devices can be used only for relaying data and those are not SNS users. For example, unmanned aerial vehicles (UAV) with D2D communication capability and base stations with D2D communication capability are used as the relay devices. In the proposed method, at first, an optimization problem for minimizing node resilience which is a performance metric in order to place relay devices. Then, we investigate how relay devices should be placed based on some approximate optimal solutions. From this investigation, we propose an autonomous relay device placement in the physical network. In our proposed algorithm, relay devices can be placed without the complete information on network topology. We evaluate the performance of the proposed method with simulation, and investigate the effectiveness of the proposed method. From numerical examples, we show the effectiveness of our proposed algorithm.

This paper proposes coded modulation for physical layer network coding in multiple input multiple output orthogonal frequency division multiplexing (MIMO-OFDM) bi-directional wireless relay systems where precoding is applied. The proposed coded modulation enables the relays to decode the received signals, which improves the transmission performance. Soft input decoding for the proposed coded modulation is proposed. Furthermore, we propose two precoder weight optimization techniques, called “per subcarrier weight optimization” and “total weight optimization”. This paper shows a precoder configuration based on the optimization with the lattice reduction or the sorted QR-decomposition. The performance of the proposed network coding is evaluated by computer simulation in a MIMO-OFDM two-hop wireless relay system with the 16 quadrature amplitude modulation (QAM) or the 256QAM. The proposed coded modulation attains a coding gain of about 2dB at the BER of 10-4. The total weight optimization achieves about 1dB better BER performance than the other at the BER of 10-4.

Silver electrical contacts were separated at constant opening speed in a 200V-500VDC/10A resistive circuit. Break arcs were extinguished by magnetic blowing-out with transverse magnetic field of a permanent magnet. The permanent magnet was appropriately located to simplify the lengthened shape of the break arcs. Magnetic flux density of the transverse magnetic field was varied from 20 to 140mT. Images of the break arcs were observed from the horizontal and vertical directions using two high speed cameras simultaneously. Arc length just before extinction was analyzed from the observed images. It was shown that shapes of the break arcs were simple enough to trace the most part of paths of the break arcs for all experimental conditions owing to simplification of the shapes of the break arcs by appropriate arrangement of the magnet. The arc length increased with increasing supply voltage and decreased with increasing magnetic flux density. These results will be discussed in the view points of arc lengthening time and arc lengthening velocity.

In emergency communication systems research, aerial wireless relay networks (AWRNs) using multicopter unmanned aerial vehicles (UAVs) have been proposed. The main issue of the AWRNs is how to minimize the delay time of packet transmissions since it is not easy to supply many multicopters to cover a wide area. In this paper, we review the flight schemes and their delay time for the AWRNs. Furthermore, the network has specific issues such as multicopters' drops due to their battery capacity depletion and inclination of moving multicopters. The inclination of multicopters affects the received power, and the communication range changes based on the inclination as well. Therefore, we clarify the effect of these issues on the delay time.

In this paper, we propose a filter-and-forward relay scheme with energy harvesting for single-carrier transmission in frequency-selective channels. The relay node harvests energy from both the source node transmit signal and its own transmit signal by self-energy recycling. The signal received by the relay node is filtered to suppress the inter-symbol interference and then forwarded to the destination node using the harvested energy. We consider a filter design method based on the signal-to-interference-plus-noise power ratio maximization, subject to a constraint that limits the relay transmit power. In addition, we provide a golden-section search based algorithm to optimize the power splitting ratio of the power splitting protocol. The simulation results show that filtering and self-energy recycling of the proposed scheme are effective in improving performance. It is also shown that the proposed scheme is useful even when only partial channel state information is available.

A novel compress-and-forward (CF) system based on multi-relay network is proposed. In this system, two networks are linked, wherein one is a sensor network connecting the analog source and the relays, and the other is a communication network between the relays and the destination. At several parallel relay nodes, the analog signals are transformed into digital signals after quantization and encoding and then the digital signals are transmitted to the destination. Based on the Chief Executive Officer (CEO) theory, we calculate the minimum transmission rate of every source-relay link and we propose a system model by combining sensor network with communication network according to Shannon channel capacity theory. Furthermore, we obtain the best possible system performance under system power constraint, which is measured by signal-to-noise ratio (SNR) rather than bit error rate (BER). Numerical simulation results show that the proposed CF outperforms the traditional amplify-and-forward (AF) system in the performance versus SNR.

The packet error rate (PER) performance of multi-hop STBC based cooperative and diversity relaying systems are studied. These systems consist of a source, a destination, and two relay stations in each hop. From in-lab experiments, it is confirmed that the cooperative relaying system has better PER performance than the diversity relaying system with highly correlated channels.