In this paper, we examine techniques for improving the throughput of unlicensed radio systems such as wireless LANs (WLANs) to take advantage of multi-radio access to mobile broadband, which will be important in 5G evolution and beyond. In WLANs, throughput is reduced due to mixed standards and the degraded quality of certain frequency channels, and thus control techniques and an architecture that provide efficient control over WLANs are needed to solve the problem. We have proposed a technique to control the terminal connection dynamically by using the multi-radio of the AP. Furthermore, we have proposed a new control architecture called WiSMA for efficient control of WLANs. Experiments show that the proposed method can solve those problems and improve the WLAN throughput.

This paper proposes a novel adaptive array configuration that reduces high-power co-channel interference (CCI) by utilizing the difference in arrival times between CCI and the desired signal in asynchronous TDD systems. The proposed adaptive array extracts only the CCI and employs pre-null steering for only the CCI by utilizing the fact that only the CCI arrives during the guard time in asynchronous TDD systems. Since the proposed adaptive array enables us to apply the Minimum Mean Square Error (MMSE) algorithm through synchronization with the desired signal using the output signal obtained by pre-null steering, high quality transmission can be achieved even in the presence of high-power CCI. Moreover, based on measurements using a fading simulator and field data, an adaptive array testbed exemplifying the proposed configuration is presented to show the reduction in the high-power CCI.

To achieve a very high data rate within a limited frequency band in orthogonal frequency division multiplexing (OFDM) systems, multi-input multi-output (MIMO) techniques are very promising. Moreover, if a transmitter has the channel state information (CSI), the achievable spectrum efficiency can be maximized using the eigenbeam-space division multiplexing (E-SDM). However, this scheme demands accurate channel estimation. Therefore, in a closed-loop transmission scheme, an increase in the amount of feedback is absolutely necessary for the E-SDM. This paper describes a downlink beamforming method that significantly reduces the amount of feedback needed by using the common transmission weight vectors in all sub-carriers, compared to the amount required for E-SDM. The proposed method also applies transmission diversity to compensate for the quality. The effectiveness of the proposed method was confirmed using computer simulations in both Ricean and Rayleigh fading environments.

A method is presented for increasing wireless LAN (WLAN) capacity in high-density environments with IEEE 802.11ax systems. We propose using coordinated scheduling of trigger frames based on our mobile cooperative control concept. High-density WLAN systems are managed by a management server, which gathers wireless environmental information from user equipment through cellular access. Hierarchical clustering of basic service sets is used to form synchronized clusters to reduce interference and increase throughput of high-density WLAN systems based on mobile cooperative control. This method increases uplink capacity by up to 19.4% and by up to 11.3% in total when WLAN access points are deployed close together. This control method is potentially effective for IEEE 802.11ax WLAN systems utilized as 5G mobile network components.

This paper proposes a hardware configuration using only single pole dual throw (SPDT) switches to realize the previously proposed automatic calibration method using transmitting signals (ACT) for the adaptive array in TDD communication systems. The proposed configuration obtains the same calibration values as the conventional ACT does while reducing the number of switch branches. The transmission pattern using the proposed calibration method is also presented based on an experimental adaptive array testbed in an actual microcell environment. The experimental results show that the ideal radiation pattern formation is achieved by employing the proposed calibration method in an environment with a moving terminal station and where arriving co-channel interference exists.

This paper proposes a channel capacity maximization method for Multiple-Input Multiple-Output (MIMO) antennas with parasitic elements. Reactive terminations are connected to the parasitic elements, and the reactance values are determined to achieve stochastically high channel capacity for the environment targeted. This method treats the S-parameter and propagation channel of the antenna, including the parasitic elements, as a combined circuit. The idea of the 'parasitic channel,' which is observed at the parasitic antenna, is introduced to simplify the optimization procedure. This method can significantly reduce the number of necessary measurements of the channel for designing the antenna. As a design example, a bidirectional Yagi-Uda array, which has two driven antennas at both ends of the linear array, is measured in an indoor environment. The resulting design offers enhanced channel capacity mainly due to its improved signal-to-noise ratio compared to the antenna without the parasitic antennas.

Path loss in high frequency bands above 6GHz is the most fundamental and significant propagation characteristic of IMT-2020. To develop and evaluate such high frequency bands, ITU-R SG5 WP5D recently released channel models applicable up to 100GHz. The channel models include path loss models applicable to 0.5-100GHz. A path loss model is used for cell design and the evaluation of the radio technologies, which is the main purpose of WP5D. Prediction accuracy in various locations, Tx positions, frequency bands, and other parameters are significant in cell design. This article presents the prediction accuracy of UMa path loss models which are detailed in Report ITU-R M.2412 for IMT-2020. We also propose UMa_A' as an extension model of UMa_A. While UMa_A applies different equations to the bands below and above 6GHz to predict path loss, UMa_A' covers all bands by using the equations of UMa_A below 6GHz. By using the UMa_A' model, we can predict path loss by taking various parameters (such as BS antenna height) into account over a wide frequency range (0.5-100GHz). This is useful for considering the deployment of BS antennas at various positions with a wide frequency band. We verify model accuracy by extensive measurements in the frequency bands from 2 to 66GHz, distances up to 1600 m, and an UMa environment with three Tx antenna heights. The UMa_A' extension model can predict path loss with the low RMSE of about 7dB at 2-26.4GHz, which is more accurate than the UMa_A and UMa_B models. Although the applicability of the UMa_A' model at 66GHz is unclear and needs further verification, the evaluation results for 66GHz demonstrate that the antenna height may affect the prediction accuracy at 66GHz.

Multiuser multiple input multiple output (MU-MIMO) systems are attracting attention due to their frequency efficiency. However, in uplink MU-MIMO systems, different frequency offsets among multiple mobile stations (MSs) significantly degrade the transmission quality, especially when orthogonal frequency division multiplexing (OFDM) is used. In this paper, the influence of these frequency offsets is first analyzed in a frequency selective fading environment. Numerical analysis shows that an error floor occurs in the bit error rate and the influence of the frequency offset becomes larger in short delay spread environments. To overcome this problem, a new beamforming method is proposed to compensate for the frequency offset by introducing an auto frequency controller after frequency-space equalization in each data stream. The effect of the proposed method is evaluated in a frequency selective fading environment by computer simulations and measured results.

Multiuser -- Multiple Input Multiple Output (MU-MIMO) techniques were proposed to increase spectrum efficiency; a key assumption was that the Mobile Terminals (MTs) were simple with only a few antennas. This paper focuses on the Block Diagonalization algorithm (BD) based on the equal power allocation strategy as a practical MU-MIMO technique. When there are many MTs inside the service area of the access point (AP), the AP must determine, at each time slot, the subset of the MTs to be spatially multiplexed. Since the transmission performance depends on the subsets of MTs, the user selection method needs to use the Channel State Information (CSI) obtained in the physical layer to maximize the Achievable Transmission Rate (ATR). In this paper, we clarify the relationship between ATR with SU-MIMO and that with MU-MIMO in a high eigenvalue channel. Based on the derived relationship, we propose a new measure for user selection. The new measure, the eigenvalue decay factor, represents the degradation of the eigenvalues in null space compared to those in SU-MIMO; it is obtained from the signal space vectors of the MTs. A user selection method based on the proposed measure identifies the combination of MTs that yields the highest ATR; our approach also reduces the computational load of user selection. We evaluate the effectiveness of user selection with the new measure using numerical formulations and computer simulations.

An OFDMA based channel access scheme is proposed for dynamic spectrum access to utilize frequency spectrum efficiently. Though the OFDMA based scheme is flexible enough to change the bandwidth and channel of the transmitted signals, the OFDMA signal has large PAPR (Peak to Average Power Ratio). In addition, if the OFDMA receiver does not use a filter to extract sub-carriers before FFT (Fast Fourier Transform) processing, the designated sub-carriers suffer large interference from the adjacent channel signals in the FFT processing on the receiving side. To solve the problems such as PAPR and adjacent channel interference encountered in the OFDMA based scheme, this paper proposes a novel dynamic channel access scheme using overlap FFT filter-bank based on single carrier modulation. It also shows performance evaluation results of the proposed scheme by computer simulation.

In this paper, we propose a novel centralized control method to handle multi-radio and terminal connections in an 802.11ax wireless LAN (802.11ax) mixed environment. The proposed control method can improve the throughput by applying 802.11ax Spatial Reuse in an environment hosting different terminal standards and mixed terminal communication quality. We evaluate the proposed control method by computer simulations assuming environments with mixed terminal standards, mixed communication quality, and both.

Combining heterogeneous wireless networks that cross licensed and unlicensed spectra is a promising way of supporting the surge in mobile traffic. The unlicensed band is mostly used by wireless LAN (WLAN) nodes which employ carrier sense multiple access/collision avoidance (CSMA/CA). Since the number of WLAN devices and their traffic are increasing, the wireless resource of the unlicensed band is expected be more depleted in 2020s. In such a wireless environment, the throughput could be extremely low and unstable due to the hidden terminal problem and exposed terminal problem despite of the large resources of the allocated frequency band and high peak PHY rate. In this paper, we propose user equipment (UE) centric access in the unlicensed band, with support by licensed band access in the mobile network. The proposed access enables robust downlink transmission from the access point (AP) to the UEs by mitigating the hidden terminal problem. The licensed spectrum access passes information on the user data waiting at the AP to the UEs and triggers UE reception opportunity (RXOP) acquisition. Furthermore, the adaptive use of UE centric downlink access is presented by using the channel utilization measured at the AP. Computer simulations confirm that licensed access assistance enhances the robustness of the unlicensed band access against the hidden terminal problem.

Over 100 Gbit/s/ch high-speed optical transmission is required to achieve the high capacity networks that can meet future demands. The coherent receiver, which is expected to yield high frequency utilization, is a promising means of achieving such high-speed transmission. However, it requires a high-speed Analog to Digital Converter (ADC) because the received signal bandwidth would be over several tens or hundreds of GHz. To solve this problem, we propose a band-divided receiver structure for wideband optical signals. In the receiver, received wideband signals are divided into a number of narrow band signals without any guard band. We develop a band-divided receiver prototype and evaluate it in an experiment. In addition, we develop a real-time OFDM demodulator on an FPGA board that implements 1.5 GS/s ADCs. We demonstrate that the band-divided receiver prototype with its real-time OFDM demodulator and 1.5 GS/s ADC can demodulate single polarization 12 Gbit/s OFDM signals in real-time.

Implicit feedback is an approach that utilizes uplink channel state information (CSI) for downlink transmit beamforming on multiple-input multiple-output (MIMO) systems, relying on over-the-air channel reciprocity. The implicit feedback improves throughput efficiency because overhead of CSI feedback for change of over-the-air channel responses is omitted. However, it is necessary for the implicit feedback to calibrate circuitry responses that uplink CSI includes, because actual downlink and uplink channel responses do not match due to different transmit and receive circuitry chains. This paper presents our proposed calibration scheme, weighted-combining calibration (WCC); it offers improved calibration accuracy. In WCC, an access point (AP) calculates multiple calibration coefficients from ratios of downlink and uplink CSI, and then combines coefficients with minimum mean square error (MMSE) weights. The weights are derived using a linear approximation in the high signal to noise power ratio (SNR) regime. Analytical mean square error (MSE) of calibration coefficients with WCC and calibration schemes for comparison is expressed based on the linear approximation. Computer simulations show that the analytical MSE matches simulated one if the linear approximation holds, and that WCC improves the MSE and signal to interference plus noise power ratio (SINR). Indoor experiments are performed on a multiuser MIMO system with implicit feedback based on orthogonal frequency division multiplexing (OFDM), built using measurement hardware. Experimental results verify that the channel reciprocity can be exploited on the developed multiuser MIMO-OFDM system and that WCC is also effective in indoor environments.

This paper proposes a novel method of reducing channel state information (CSI) feedback by using transmit antenna selection for downlink multiuser multiple input multiple output (DL-MU-MIMO) transmission in dense distributed antenna systems. It is widely known that DL-MU-MIMO transmission achieves higher total bit-rate by mitigating inter-user interference based on pre-coding techniques. The pre-coding techniques require CSI between access point (AP) and multiple users. However, overhead for CSI acquisition degrades the transmission efficiency of DL-MU-MIMO transmission. In the proposed CSI feedback reduction method, AP first selects the antenna set that maximizes the received power at each user, second it skips the sequence of CSI feedback for users whose signal to interference power ratio is larger than a threshold, and finally it performs DL-MU-MIMO transmission to multiple users by using the selected antenna set. To clarify the proposed method, we evaluate it by computer simulations in an indoor scenario. The results show that the proposed method can offer higher transmission efficiency than the conventional DL-MU-MIMO transmission with the usual CSI feedback method.

Dense deployments of wireless local area network (WLAN) access points (APs) are accelerating to accommodate the massive wireless traffic from various mobile devices. The AP densification improves the received power at mobile devices; however, total throughput in a target area is saturated by inter-cell interference (ICI) because of the limited number of frequency channels available for WLANs. To substantially mitigate ICI, we developed and described a distributed smart antenna system (D-SAS) proposed for dense WLAN AP deployment in this paper. We also describe a system configuration based on our D-SAS approach. In this approach, the distributed antennas externally attached to each AP can be switched so as to make the transmit power match the mobile device's conditions (received power and packet type). The gains obtained by the antenna switching effectively minimize the transmission power required of each AP. We also describe experimental measurements taken in a stadium using a system prototype, the results show that D-SAS offers double the total throughput attained by a centralized smart antenna system (C-SAS).

Multiple input multiple output (MIMO) systems represent a very attractive candidate for future high data rate wireless access systems to increase the channel capacity. To obtain a further increase in the channel capacity, a distributed wireless communication system that has multiple access points (APs) and an access controller (AC), was proposed. This system increases not only the peak transmission rate but also the overall transmission rate in the service area. In this paper, we consider a cooperative multiple AP system where APs are synchronized in terms of time, but not in terms of phase. We propose a transmission method for the cooperative multiple AP system that enables the mobile station to obtain a high achievable bit rate regardless of decoding algorithms. The performance of the multiple AP systems is evaluated in comparison to the conventional single AP system. To evaluate the effectiveness of the proposed method in the cooperative multiple AP system, computer simulations are performed using the i.i.d. channel in Rayleigh and Ricean fading environments. Furthermore, we evaluate the performance of the cooperative multiple AP system using the channel measured in an actual indoor environment.

This paper proposes a radio propagation prediction method that uses point cloud data based on a hybrid of the ray-tracing (RT) method and an effective roughness (ER) model in urban environments for the fifth generation mobile communications system using high frequency bands. The proposed prediction method incorporates propagation characteristics that consider diffuse scattering from surface irregularities. The validity of the proposed method is confirmed by comparisons of measurement and prediction results gained from the proposed method and a conventional RT method based on power delay and angular profiles. From predictions based on the power delay and angular profiles, we find that the proposed method, assuming the roughness of σh=1mm, accurately predicts the propagation characteristics in the 20GHz band for urban line-of-sight environments. The prediction error for the delay spread is 2.1ns to 9.7ns in an urban environment.

This paper proposes a hardware configuration for uplink multi-user multiple-input multiple-output (MU-MIMO) transmissions in a distributed antenna system (DAS). The demand for high-speed transmission in the uplink has increased recently, because of which standardizations in LTE-advanced and IEEE 802.11ax networks is currently underway. User terminal (UT) scheduling on the downlink MU-MIMO transmission is easy even in unlicensed band such as those in wireless local area network (WLAN) systems. However, the detailed management of the UTs is difficult on the uplink MU-MIMO transmissions because of the decentralized wireless access control. The proposed configuration allows an antenna to be selected from an external device on the access point (AP). All AP antennas are divided into groups, and the received signal in each group is input to the amplitude detector via a directional coupler. Subsequently, the selected antenna is fed by a multiple-to-one switch instead of a matrix switch. To clarify the effectiveness of the proposed configuration, we conduct computer simulations based on the ray-tracing method for propagation channels in an indoor environment.

Recently, Multiple Input Multiple Output-Orthogonal Frequency Division Multiplexing (MIMO-OFDM) has attracted much attention as a technology achieving high-speed wireless transmission with a limited bandwidth. However, since bit loading and adaptive modulation per sub-carrier should be employed according to the transmission quality of each sub-carrier in MIMO-OFDM, it is very important to understand the frequency correlation characteristics in broadband MIMO channels. This paper investigates the frequency correlation characteristics based on the antenna configuration for actual indoor MIMO channels. The results show that the frequency correlation of the channel capacity for the array antenna configured in the horizontal plane is significantly different compared to that configured in the vertical plane. Moreover, we propose a new cluster model that considers the antenna configuration in both the horizontal and vertical planes to estimate the frequency correlation in broadband MIMO channels.