A method for runtime energy optimization based on the supply voltage (Vdd) and the threshold voltage (Vth) scaling is proposed. This paper refers to the optimal voltage pair, which minimizes the energy consumption of LSI circuits under a target delay constraint, as a Minimum Energy Point (MEP). The MEP dynamically fluctuates depending on the operating conditions determined by a target delay constraint, an activity factor and a chip temperature. In order to track the MEP, this paper proposes a closed-form continuous function that determines the MEP over a wide operating performance region ranging from the above-threshold region down to the sub-threshold region. Based on the MEP determination formula, an MEP tracking algorithm is also proposed. The MEP tracking algorithm estimates the MEP even though the operating conditions widely change. Measurement results based on a 32-bit RISC processor fabricated in a 65-nm Silicon On Thin Buried oxide (SOTB) process technology show that the proposed method estimates the MEP within a 5% energy loss in comparison with the actual MEP operation.

This paper proposes an area- and energy-efficient DLL-based body bias generator (BBG) for minimum energy operation that controls p-well and n-well bias independently. The BBG can minimize total energy consumption of target circuits under a skewed process condition between nMOSFETs and pMOSFETs. The proposed BBG is composed of digital cells compatible with cell-based design, which enables energy- and area-efficient implementation without additional supply voltages. A test circuit is implemented in a 65-nm FDSOI process. Measurement results using a 32-bit RISC processor on the same chip show that the proposed BBG can reduce energy consumption close to a minimum within a 3% energy loss. In this condition, energy and area overheads of the BBG are 0.2% and 0.12%, respectively.

A non-volatile memory (NVM) employing MTJ has a lot of strong points such as read/write performance, best endurance and operating-voltage compatibility with standard CMOS. However, it consumes a lot of energy when writing the data. This becomes an obstacle when applying to battery-operated mobile devices. To solve this problem, we propose an approach to augment the capability of the precision scaling technique for the write operation in NVM. Precision scaling is an approximate computing technique to reduce the bit width of data (i.e. precision) for energy reduction. When writing image data to NVM with the precision scaling, the write energy and the image quality are changed according to the write time and the target bit range. We propose an energy-efficient approximate storing scheme for non-volatile flip-flops and a magnetic random-access memory (MRAM) that allows us to write the data by optimizing the bit positions to split the data and the write time for each bit range. By using the statistical model, we obtained optimal values for the write time and the targeted bit range under the trade-off between the write energy reduction and image quality degradation. Simulation results have demonstrated that by using these optimal values the write energy can be reduced up to 50% while maintaining the acceptable image quality. We also investigated the relationship between the input images and the output image quality when using this approach in detail. In addition, we evaluated the energy benefits when applying our approach to nine types of image processing including linear filters and edge detectors. Results showed that the write energy is reduced by further 12.5% at the maximum.

This paper studies a harvested power-oriented simultaneous wireless information and power transfer (SWIPT) scheme over multiple-input multiple-output (MIMO) interference channels in which energy harvesting (EH) circuits exhibit nonlinearity. To maximize the power harvested by all receivers, we propose an algorithm to jointly optimize the transmit beamforming vectors, power splitting (PS) ratios and the receive decoding vectors. As all variables are coupled to some extent, the problem is non-convex and hard to solve. To deal with this non-convex problem, an iterative optimization method is proposed. When two variables are fixed, the third variable is optimized. Specifically, when the transmit beamforming vectors are optimized, the transferred objective function is the sum of several fractional functions. Non-linear sum-of-ratios programming is used to solve the transferred objective function. The convergence and advantage of our proposed scheme compared with traditional EH circuits are validated by simulation results.

In vacuum-deposited film composed of organic polar molecules, polarization charges appear on the film surface owing to spontaneous orientation of the molecule. Because its density (σpol) determines an amount of accumulation charge (σacc) in organic light-emitting diodes and output power in polar molecular-based vibrational energy generators (VEGs), control of molecular orientation is highly required. Recently, several groups have reported that dipole-dipole interaction between polar molecules induces anti-parallel orientation which does not contribute to σpol. In other words, perturbation inducing the attenuation of the dipole interaction is needed to enhance σpol. In this study, to investigate an effect of light irradiation on σpol, we prepared 1,3,5-tris(1-phenyl-1H-benzimidazol-2-yl)benzene (TPBi) film under illumination during its deposition, and evaluated the σacc in TPBi-based bilayer device, which equals to σpol. We found that the σacc was increased by light irradiation, indicating that average orientation of TPBi is enhanced. These results suggest that light irradiation during device fabrication is promising process for organic electronic devices including polar molecule-based VEGs.

Because solar energy is intermittent and a ship's power-system load fluctuates and changes abruptly, in this work, the solar radiation parameters were adjusted according to the latitude and longitude of the ship and the change of the sea environment. An objective function was constructed that accounted for the cost and service life simultaneously to optimize the configuration of the marine diesel engine hybrid energy system. Finally, the improved artificial bee colony algorithm was used to optimize and obtain the optimal system configuration. The feasibility of the method was verified by ship navigation tests. This method exhibited better configuration performance optimization than the traditional methods.

Scalable networking for scientific research data transfer is a vital factor in the progress of data-intensive research, such as collaborative research on observation of black hole. In this paper, investigations of the nature of practical research traffic allow us to introduce optical flow switching (OFS) and contents delivery network (CDN) technologies into a wide area network (WAN) to realize highly scalable networking. To measure the scalability of networks, energy consumption in the WAN is evaluated by considering the practical networking equipment as well as reasonable assumptions on scientific research data transfer networks. In this study, we explore the energy consumption performance of diverse Japan and US topologies and reveal that the energy consumption of a routing and wavelength assignment algorithm in an OFS scheduler becomes the major hurdle when the number of nodes is high, for example, as high as that of the United States of America layer 1 topology. To provide computational scalability of a network dimensioning algorithm for the CDN based WAN, a simple heuristic algorithm for a surrogate location problem is proposed and compared with an optimal algorithm. This paper provides intuitions and design rules for highly scalable research data transfer networks, and thus, it can accelerate technology advancements against the encountering big-science problems.

In this paper, we advocate applying the concept of content-based wake-up to distributed estimation in wireless sensor networks employing wake-up receivers. With distributed estimation, where sensing data of multiple nodes are used for estimating a target observation, the energy consumption can be reduced by ensuring that only a subset of nodes in the network transmit their data, such that the collected data can guarantee the required estimation accuracy. In this case, a sink needs to selectively wake up those sensor nodes whose data can contribute to the improvement of estimation accuracy. In this paper, we propose wake-up signaling called estimative sampling (ES) that can selectively activate the desired nodes by using content-based wake-up control. The ES method includes a mechanism that dynamically searches for the desired nodes over a distribution of sensing data. With numerical results obtained by computer simulations, we show that the distributed estimation with ES method achieves lower energy consumption than conventional identity-based wake-up while satisfying the required accuracy. We also show that the proposed dynamic mechanism finely controls the trade-off between delay and energy consumption to complete the distributed estimation.

Delay Tolerant Networks (DTNs) are vulnerable to message flooding attacks in which a very large number of malicious messages are sent so that network resources are depleted. To address this problem, previous studies mainly focused on constraining the number of messages that nodes can generate per time slot by allowing nodes to monitor the other nodes' communication history. Since the adversaries may hide their attacks by claiming a false history, nodes exchange their communication histories and detect an attacker who has presented an inconsistent communication history. However, this approach increases node energy consumption since the number of communication histories increases every time a node communicates with another node. To deal with this problem, in this paper, we propose an energy-efficient defense against such message flooding attacks. The main idea of the proposed scheme is to time limit the communication history exchange so as to reduce the volume while ensuring the effective detection of inconsistencies. The advantage of this approach is that, by removing communication histories after they have revealed such inconsistencies, the energy consumption is reduced. To estimate such expiration time, analytical expressions based upon a Markov chain based message propagation model, are derived for the probability that a communication history reveals such inconsistency in an arbitrary time. Extensive performance evaluation results obtained by means of computer simulations and several performance criteria verify that the proposed scheme successfully improves the overall energy efficiency. For example, these performance results have shown that, as compared to other previously known defenses against message flooding attacks, the proposed scheme extends by at least 22% the battery lifetime of DTN nodes, while maintaining the same levels of protection.

A temperature-variation-tolerant intermittent startup circuit (ISC) that suppresses quiescent current to 300nA at 0.48V was developed. The ISC is a key circuit for a batteryless wireless sensor that can detect a 1μA generation current of energy harvesting sources from the intervals of wireless signals. The ISC consists of an ultralow-voltage detector composed of a depletion-type MOSFET and low-Vth MOSFETs, a Dickson-type gate-boosted charge pump circuit, and a power-switch control circuit. The detector consists of a voltage reference comparator and a feedback-controlled latch circuit for a hysteresis function. The voltage reference comparator, which has a common source stage with a folded constant-current-source load composed of a depletion-type nMOSFET, makes it possible to reduce the temperature dependency of the detection voltage, while suppressing the quiescent current to 300nA at 0.48V. The ISC fabricated with fully-depleted silicon-on-insulator (FD-SOI) CMOS technology also suppresses the variation of the quiescent current. To verify the effectiveness of the circuit, the ISC was fabricated in a 0.8-μm triple-Vth FD-SOI CMOS process. An experiment on the fabricated system, the ISC boosts the input voltage of 0.48V to 2.4V while suppressing the quiescent current to less than 300nA at 0.48V. The measured temperature coefficient of the detection voltage was ±50ppm/°C. The fluctuation of the quiescent current was 250nA ± 90nA in the temperature range from 0°C to 40°C. An intermittent energy harvesting sensor with the ISC was also fabricated. The sensor could detect a generation current of 1μA at EH sources within an accuracy of ±15% in the temperature range from 0°C to 40°C. It was also successfully applied to a self-powered wireless plant-monitoring sensor system.

In this paper, we clarify the importance of performance evaluation using a plurality of smartphones in a positioning system based on radio waves. Specifically, in a positioning system using bluetooth low energy, the positioning performance of two types of positioning algorithms is performed using a plurality of smartphones. As a result, we confirmed that the fingerprint algorithm does not always provide sufficient positioning performance. It depends on the model of the smartphone used. On the other hand, the hybrid algorithm that the authors have already proposed is robust in the difference of the received signal characteristics of the smartphone. Consequently, we spotlighted that the use of multiple devices is essential for providing high-quality location-based services in real environments in the performance evaluation of radio wave-based positioning systems using smartphones.

This paper proposes iterative carrier frequency offset (CFO) compensation for spatially multiplexed Bluetooth Low Energy (BLE) signals using independent component analysis (ICA). We apply spatial division multiple access (SDMA) to BLE system to deal with massive number of connection requests of BLE devices expected in the future. According to specifications, each BLE peripheral device is assumed to have CFO of up to 150 [kHz] due to hardware impairments. ICA can resolve spatially multiplexed signals even if they include independent CFO. After the ICA separation, the proposed scheme compensates for the CFO. However, the length of the BLE packet preamble is not long enough to obtain accurate CFO estimates. In order to accurately conduct the CFO compensation using the equivalent of a long pilot signal, preamble and a part of estimated data in the previous process are utilized. In addition, we reveal the fact that the independent CFO of each peripheral improves the capability of ICA blind separation. The results confirm that the proposed scheme can effectively compensate for CFO in the range of up to 150[kHz], which is defined as the acceptable value in the BLE specification.

With the development of cloud computing, the Mobile Edge Computing has emerged and attracted widespread attentions. In this paper, we focus on the load balancing in MEC with energy harvesting. We first introduce the load balancing in MEC as a problem of minimizing both the energy consumption and queue redundancy. Thereafter, we adapt such a optimization problem to the Lyapunov algorithm and solve this optimization problem. Finally, extensive simulation results validate that the obtained strategy improves the capabilities of MEC systems.

In an internet of things (IoT) system using an energy harvesting device and a secondary (2nd) battery, regardless of the age of the 2nd battery, the power management shortens the lifespan of the entire system. In this paper, we propose a scheme that extends the lifetime of the energy harvesting-based IoT system equipped with a Lithium 2nd battery. The proposed scheme includes several policies of using a supercapacitor as a primary energy storage, limiting the charging level according to the predicted harvesting energy, swinging the energy level around the minimum stress state of charge (SOC) level, and delaying the charge start time. Experiments with natural solar energy measurements based on a battery aging approximation model show that the proposed method can extend the operation lifetime of an existing IoT system from less than one and a half year to more than four years.

Two-ray (TR) fading model is one of the fading models to represent a worst-case fading scenario. We derive the exact closed-form expressions of the generalized moment generating function (G-MGF) for the TR fading model, which enables us to analyze the numerous types of wireless communication applications. Among them, we carry out several analytical results for the TR fading model, including the exact ergodic capacity along with asymptotic expressions and energy detection performance. Finally, we provide numerical results to validate our evaluations.

This paper discusses and elaborates an analytical model of a multi-stage switched-capacitor (SC) voltage boost converter (VBC) for low-voltage and low-power energy harvesting systems, because the output impedance of the VBC, which is derived from the analytical model, plays an important role in the VBC's performance. In our proposed method, we focus on currents flowing into input and output terminals of each stage and model the VBCs using switching frequency f, charge transfer capacitance CF, load capacitance CL, and process dependent parasitic capacitance's parameter k. A comparison between simulated and calculated results showed that our model can estimate the output impedance of the VBC accurately. Our model is useful for comparing the relative merits of different types of multi-stage SC VBCs. Moreover, we demonstrate the performance of a prototype SC VBC and energy harvesting system using the SC VBC to show the effectiveness and feasibility of our proposed design guideline.

Radio frequency energy transfer (RET) technology has been introduced as a promising energy harvesting (EH) method to supply power in both wireless communication (WLC) and power-line communication (PLC) systems. However, current RET modified MAC (medium access control) protocols have been proposed only for WLC systems. Due to the difference in the MAC standard between WLC and PLC systems, these protocols are not suitable for PLC systems. Therefore, how to utilize RET technology to modify the MAC protocol of PLC systems (i.e., IEEE 1901), which can use the radio frequency signal to provide the transmission power and the PLC medium to finish the data transmission, i.e., realizing the ‘cooperative communication’ remains a challenge. To resolve this problem, we propose a RET modified MAC protocol for PLC systems (RET-PLC MAC). Firstly, we improve the standard PLC frame sequence by adding consultation and confirmation frames, so that the station can obtain suitable harvested energy, once it occupied the PLC medium, and the PLC system can be operated in an on-demand and self-sustainable manner. On this basis, we present the working principle of RET-PLC MAC. Then, we establish an analytical model to allow mathematical verification of RET-PLC MAC. A 2-dimension discrete Markov chain model is employed to derive the numerical analysis results of RET-PLC MAC. The impacts of buffer size, traffic rate, deferral counter process of 1901, heterogeneous environment and quality of information (QoI) are comprehensively considered in the modeling process. Moreover, we deduce the optimal results of system throughput and expected QoI. Through extensive simulations, we show the performance of RET-PLC MAC under different system parameters, and verify the corresponding analytical model. Our work provides insights into realizing cooperative communication at PLC's MAC layer.

In this paper, we propose a filter-and-forward relay scheme with energy harvesting for single-carrier transmission in frequency-selective channels. The relay node harvests energy from both the source node transmit signal and its own transmit signal by self-energy recycling. The signal received by the relay node is filtered to suppress the inter-symbol interference and then forwarded to the destination node using the harvested energy. We consider a filter design method based on the signal-to-interference-plus-noise power ratio maximization, subject to a constraint that limits the relay transmit power. In addition, we provide a golden-section search based algorithm to optimize the power splitting ratio of the power splitting protocol. The simulation results show that filtering and self-energy recycling of the proposed scheme are effective in improving performance. It is also shown that the proposed scheme is useful even when only partial channel state information is available.

In this paper, the artificial noise (AN)-aided multiple-input single-output (MISO) cognitive radio network with simultaneous wireless information and power transfer (SWIPT) is considered, in which the cognitive user adopts the power-splitting (PS) receiver architecture to simultaneously decode information and harvest energy. To support secure communication and facilitate energy harvesting, AN is transmitted with information signal at cognitive base station (CBS). The secrecy energy efficiency (SEE) maximization problem is formulated with the constraints of secrecy rate and harvested energy requirements as well as primary user's interference requirements. However, this challenging problem is non-convex due to the fractional objective function and the coupling between the optimization variables. For tackling the challenging problem, a double-layer iterative optimization algorithm is developed. Specifically, the outer layer invokes a one-dimension search algorithm for the newly introduced tight relaxation variable, while the inner one leverages the Dinkelbach method to make the fractional optimization problem more tractable. Furthermore, closed-form expressions for the power of information signal and AN are obtained. Numerical simulations are conducted to demonstrate the efficiency of our proposed algorithm and the advantages of AN in enhancing the SEE performance.

Green cognitive radio (CR) plays an important role in offering secondary users (SUs) with more spectrum with smaller energy expenditure. However, the energy efficiency (EE) issues associated with green CR for fading channels have not been fully studied. In this paper, we investigate the average EE maximization problem for spectrum-sharing CR in fading channels. Unlike previous studies that considered either the peak or the average transmission power constraints, herein, we considered both of these constraints. Our aim is to maximize the average EE of SU by optimizing the transmission power under the joint peak and average transmit power constraints, the rate constraint of SU and the quality of service (QoS) constraint of primary user (PU). Specifically, the QoS for PU is guaranteed based on either the average interference power constraint or the PU outage constraint. To address the non-convex optimization problem, an iterative optimal power allocation algorithm that can tackle the problem efficiently is proposed. The optimal transmission powers are identified under both of perfect and imperfect channel side information (CSI). Simulations show that our proposed scheme can achieve higher EE over the existing scheme and the EE achieved under perfect CSI is better than that under imperfect CSI.