The large signal performance and model for GaN FET devices was evaluated with DC, S-parameters, and large signal measurements. The large signal model was extended with bias and temperature dependence of access resistances, modified capacitance and charge equations, as well as breakdown models. The model was implemented in a commercial CAD tool and exhibits good overall accuracy.

A fiber Bragg grating, which has periodical perturbation of the refractive index in the fiber core, acts as a wavelength selective reflection filter and steep optical spectrum can be realized by forming more than ten thousand of gratings along the fiber core. Owing to capability of making steep optical spectrum, fiber Bragg gratings has been expected to be introduced practical use as multiplexing or demultiplexing filters in dense WDM transmission systems. On the other hand, radiation mode loss, reflection side mode and temperature dependence of Bragg wavelength, should be improved to put the fiber Bragg grating to practical use in dense WDM transmission systems. In this paper, an optimum design and performance of the fiber Bragg grating for dense WDM systems are described. The photosensitive cladding fiber realized less than 0. 2 dB insertion loss at transmitted signal channels and less than 0. 1 dB splicing loss with standard single-mode fibers. An adequate apodization technique in the refractive index distribution suppressed reflection side modes. A temperature compensating package, which gives longitudinal strain with negative temperature dependence to a fiber Bragg grating, minimized temperature dependence of Bragg wavelength less than 0. 001 nm/. Thermal decay of Bragg grating was also investigated and adequate annealing condition was estimated to obtain sufficient stability for practical use in dense WDM transmission.

This paper proposes a new face recognition method based on mutual projection of feature distributions. The proposed method introduces a new robust measurement between two feature distributions. This measurement is computed by a harmonic mean of two distance values obtained by projection of each mean value into the opposite feature distribution. The proposed method does not require eigenvalue analysis of the two subspaces. This method was applied to face recognition task of temporal image sequence. Experimental results demonstrate that the computational cost was improved without degradation of identification performance in comparison with the conventional method.

This paper reports the new gate and recess structure design of millimeter-wave, high power pHEMTs, which highly improves humidity resistance and reliability. By using tantalum nitride as the refractory gate metal and a silicon nitride layer prepared by a catalytic chemical vapor deposition technique for passivation of this transistor, strong moisture resistance was obtained without degradation of the device characteristics. Moreover, we have designed a stepped recess structure to increase the on-state breakdown voltage without degradation of the power density of the millimeter-wave pHEMT, according to the analysis based on the new nonlinear drain resistance model. Consequently, the developed pHEMT has shown strong humidity resistance with no degradation of the DC characteristics even after 1000 hours storage at 400 K and 85% humidity, and the high on-state breakdown voltage of over 30 V while keeping the high power density of 0.65 W/mm in the Ka band. In addition, the proposed nonlinear drain resistance model effectively explains this power performance.

A microwave waveform measurement system below 18 GHz was developed and verified with a conventional RF measurement. The current and voltage RF waveforms of AlGaAs HBTs at the fundamental frequency of 1 GHz were directly measured with the system. A new direct method of sweeping and measuring dynamic RF load lines is proposed to measure the operating limits of the device. The maximum operating region was experimentally investigated with this method. The limits with a small input power are found to come from thermal runaway and the avalanche breakdown of the device. With a large input power, the HBT was found to operate beyond the DC limit of thermal runaway. The base ballasting resistance was also found to enhance large signal operating limits beyond those expected from the conventional DC theory.

A novel millimeter-wave on-wafer CAT(Computer-Aided-Testing ) system has been developed for measurement of S-parameters and NF ( Noise figure ). For the S-parameter test system, we have developed a holder setup and installed it in a semi-automatic wafer prober so that the waveguide-based T/R module can be directly connected to a probe-head through fixed waveguides, which feature low insertion loss of less than 2 dB, from 75 GHz to 98 GHz. The accuracy of the developed test system was confirmed by measuring, with this system, a co-planar offset short pattern then comparing measured and simulated results. A good agreement between the measured and calculated, in both return loss and return phase successfully demonstrated the superiority of the system. A W-band NF test system with a system noise of less than 8 dB has been also developed to provide an on-wafer NF measurement capability with an accuracy of 0.3 dB. These S-parameter and NF test systems possess great advantages to achieve high-speed automatic MMIC testing up to W-band.

For the purpose of applying to 50 GHz channel spacing 10 Gb/s DWDM systems, the dispersion reduced fiber Bragg gratings (FBG) is demonstrated. This new FBG is designed by applying in optimized cosine expansion series to the refractive index profile. The 10 π-phase shifts in the refractive index profile realize both square filtering characteristics and linear phase responses resulting in reducing group delay variation in the reflective bandwidth. The FBG, fabricated according to the new design, is tested and shows more than 30 dB isolation for the adjacent channel and less than 10 psec group delay variation in the reflective bandwidth. This small dispersion leads to vast improvement of 10 Gb/s transmission performance. The power penalty of the new FBG is suppressed to 1/6 of that of conventional FBG. Furthermore, the symmetrical refractive index profile, realized by applying a cosine expansion series, shows that these optical characteristics have no dependence of the light launching direction. From these results, this new design offers an FBG suitable for the ADM used in 10 Gb/s DWDM systems.

We present a high performance AlGaAs/GaAs power HBT with very low thermal resistance for digital cellular phones. Device structure with emitter air-bridge is utilized and device layout is optimized to reduce thermal resistance based on three-dimensional thermal flow analysis, and in spite of a rather thick substrate (100 µm), which achieved a low thermal resistance of 23/W for a multi-finger (440 µm240 fingers) HBT. This 40 finger HBT achieved power added efficiency (PAE) of over 53%, 29.1 dBm output power (Pout) and high associated gain (Ga) of 13.5 dB with 50 kHz adjacent channel leakage power (Padj) of less than -48 dBc under a 948 MHz π/4-shifted QPSK modulation with 3.4 V emitter-collector voltage. We also investigated the difference of RF performance between two bias modes (constant base voltage and current), and found which mode is adequate for each stage in several stage power amplifier for the first time.

A high directivity microstrip coupler suppressing leak coupling with a cancellation circuit of a Wilkinson divider is presented. The presented coupler utilizes a cancellation circuit between a coupling port and an isolation port of the conventional microstrip coupler to enhance the isolation. The cancellation circuit consists of the Wilkinson divider, the multistage attenuator, and the phase offset line. The frequency to enhance the isolation is controlled by the attenuators. As the directivity is improved without the modification of the conventional coupler, the cancellation circuit can be applied to the fabricated conventional couplers. The measured directivity of the presented 1/18 λ coupler is improved from 4.8 dB to 43.0 dB at 2.6 GHz, compared with the conventional 1/4 λ coupler with -20 dB coupling. Simultaneously, the 27.4% relative bandwidth with the 20 dB directivity is achieved.

This paper discusses design of Generalized Predictive Control (GPC) scheme. GPC is designed in two cases; the first is a dual-rate (DR) system, where the sampling interval of a plant output is an integer multiple of the holding interval of a control input, and the second is a fast-rate single-rate (FR-SR) system, where both the holding and sampling intervals are equal to the holding interval of the DR system. Furthermore, the relation between them is investigated, and this study gives the conditions that FR-SR and DR GPC become equivalent. To this end, a future reference trajectory of DR GPC is rewritten, and a future predictive output of the FR-SR GPC is rearranged.

The performance of recently developed Large Signal (LS) HBT model was evaluated with extensive LS measurements like Power spectrum, Load pull and Inter-modulation investigations. Proposed model has adopted temperature dependent leakage resistance and a simplified capacitance models. The model was implemented in ADS as SDD. Important feature of the model is that the main model parameters are taken directly from measurements in rather simple and understandable way. Results show good accuracy despite the simplicity of the model. To our knowledge the HBT model is one of a few HBT models which can handle high current & Power HBT devices, with significantly less model parameters with good accuracy.

A matched load for post-wall waveguide (SIW; Substrate Integrated Waveguide) is presented. It consists of an electrically-shorted post-wall waveguide and a rectangular thin-film resistor sheet on the surface of the waveguide, resulting in a quite compact structure without three-dimensional bulky absorber as in conventional waveguide matched loads. A fabricated X-band matched load has achieved less than -20 dB reflection in more than 20% relative bandwidth.

This paper describes a 3.5 V operation InGaP HBT MMIC power amplifier module for use in GSM/EDGE dual-mode, 900/1800/1900 MHz triple band handset applications. Conventional GSM amplifiers have a high linear gain of 40 dB or more to realize efficiency operation in large gain compression state exceeding at least 5 dB. On the other hand, an EDGE amplifier needs a linear operation to prevent signal distortion. This means that a high linear gain amplifier cannot be applied to the EDGE amplifier, because the high gain leads to the high noise power in the receive band (Rx-noise). In order to solve this problem, we have changed the linear gain of the amplifier between GSM and EDGE mode. In EDGE mode, the stage number of the amplifier changes from three to two. To reduce a high gain, the first stage transistors in the amplifier is bypassed through the diode switches. This newly proposed bypass circuit enables a high gain in GSM mode and a low gain in EDGE, thus allowing the amplifier to operate with high efficiency in both modes while satisfying the Rx-noise specification. In conclusion, with diode switches and a band select switch built on the MMIC, the module delivers a Pout of 35.5 dBm and a PAE of about 50% for GSM900, a 33.4 dBm Pout and a 45% PAE for GSM1800/1900. While satisfying an error vector magnitude (EVM) of less than 4% and a receive-band noise power of less than -85 dBm/100 kHz, the module also delivers a 29.5 dBm Pout and a PAE of over 25% for EDGE900, a 28.5 dBm Pout and a PAE of over 25% for EDGE1800/1900.

We have developed a novel human facial tracking system that operates in real time at a video frame rate without needing any special hardware. The approach is based on the use of Lie algebra, and uses three-dimensional feature points on the targeted human face. It is assumed that the roughly estimated facial model (relative coordinates of the three-dimensional feature points) is known. First, the initial feature positions of the face are determined using a model fitting technique. Then, the tracking is operated by the following sequence: (1) capture the new video frame and render feature points to the image plane; (2) search for new positions of the feature points on the image plane; (3) get the Euclidean matrix from the moving vector and the three-dimensional information for the points; and (4) rotate and translate the feature points by using the Euclidean matrix, and render the new points on the image plane. The key algorithm of this tracker is to estimate the Euclidean matrix by using a least square technique based on Lie algebra. The resulting tracker performed very well on the task of tracking a human face.

The maximum operating region of a SiGe HBT has been experimentally investigated by a direct microwave waveform measurement. Dynamic RF load lines are used as a probe to detect the limit of the RF operation. For the first time, it is found that SiGe HBTs operate beyond the conventional BVceo, while GaAs HBTs cannot survive at that voltage. The conventional BVceo limits the average Vc of the maximum load lines, but has no influence on the peak voltage. Another BVceo measured with a voltage generator is proposed to represent the irreversible avalanche breakdown instead of the conventional one. A pulsed breakdown measurement is also performed to reveal the time constant of the phenomena.

This paper proposes a new method for automatic improvement in image quality through adjusting the image sharpness. This method does not need prior knowledge about image blur. To improve image quality, the sharpness must be adjusted to an optimal value. This paper shows a new method to evaluate sharpness without MTF. It is considered that the human visual system judges image sharpness mainly based upon edge area features. Therefore, attention is paid to the high spatial frequency components in the edge area. The value is defined by the average intensity of the high spatial fequency components in the edge area. This is called the image edge sharpness" value. Using several images, edge sharpness values are compared with experimental results for subjective sharpness. According to the experiments, the calculated edge sharpness values show a good linear relation with subjective sharpness. Subjective image sharpness does not have a monotonic relation with subjective image quality. If the edge sharpness value is in a particular range, the image quality is judged to be good. According to the subjective experiments, an optimal edge sharpness value for image quality was obtained. This paper also shows an algorithm to alter an image into one which has another edge sharpness value. By altering the image, which achieves optimal edge sharpness using this algorithm, image sharpness can be optimally adjusted automatically. This new image improving method was applied to several images obtained by scanning photographs. The experimental results were quite good.

A new harmonic termination that controls the waveform of the drain current to be rectangular is developed for high-efficiency power amplifier modules. Its harmonic termination is a short circuit at the third harmonic and a non-short circuit at the second harmonic. It is found experimentally and confirmed by simulation that the load-matching condition at the third-order harmonic improves the efficiency of a transistor by more than 13%. By using this tuning, 57.7% power-added efficiency of the module is achieved at the output power of 29.9 dBm with ACP of -50 dBc, NACP of -65 dBc at 925 MHz and Vdd of 3.5 V.

In this paper, we are concerned with a problem of obtaining an approximate solution of a finite-dimensional nonlinear equation with guaranteed accuracy. Assuming that an approximate solution of a nonlinear equation is already calculated by a certain numerical method, we present computable conditions to validate whether there exists an exact solution in a neighborhood of this approximate solution or not. In order to check such conditions by computers, we present a method using rational arithmetic. In this method, both the effects of the truncation errors and the rounding errors of numerical computation are taken into consideration. Moreover, based on rational arithmetic we propose a new modified Newton interation to obtain an improved approximate solution with desired accuracy.