This paper introduces a wireless-powered relay transceiver designed to extend 5G millimeter-wave coverage. It employs an on-chip butler matrix, enabling beam control-free operation. The prototype includes PCB array antennas and on-chip butler matrix and rectifiers manufactured using a Si CMOS 65 nm process. The relay transceiver performs effectively in beam angles from -45° to 45°. In the 24 GHz wireless power transmission (WPT) mode, it generates 0.12 mW with 0 dBm total input power, boasting an RF-DC conversion efficiency of 12.2%. It also demonstrates communication performance at 28 GHz in both RX and TX modes with a 100 MHz bandwidth and 64QAM modulation.

This paper proposes a multibeam digital predistorter (DPD) that suppresses intercarrier interference caused by nonlinear distortions of power amplifiers (PAs) while reducing the power consumption of a multibeam array antenna transmitter. The proposed DPD reduces power consumption by allowing the final PAs of the array antenna transmitter to operate in a highly efficient nonlinear mode and compensating for the nonlinear distortions of the PAs with a unified dedicated DPD per subarray. Additionally, it provides the required high-quality signal transmission for high throughputs, such as realizing a 256-quadrature amplitude modulation (QAM) transmission instead of a 64-QAM transmission. Specifically, it adds an inverse-component signal to cancel the interference from an adjacent carrier of another beam. Consequently, it can suppress the intercarrier interference in the beam direction and improve the error vector magnitude (EVM) during the multibeam transmission, in which the frequency bands of the beams are adjacent. The experimental results obtained for two beams at 28.0 and 28.4GHz demonstrate that, compared with the previous single-beam DPD, the proposed multibeam DPD can improve the EVM. Also, they demonstrate that the proposed DPD can achieve an EVM value of <3%, which completely satisfies the 3GPP requirements for a 256-QAM transmission.

In 5th generation (5G) and Beyond 5G mobile communication systems, it is expected that numerous antennas will be densely deployed to realize ultra-broadband communication and uniform coverage. However, as the number of antennas increases, total power consumption of all antennas will also increase, which leads to a negative impact on the environment and operating costs of telecommunication operators. Thus, it is necessary to simplify an antenna structure to suppress the power consumption of each antenna. On the other hand, as a way to realize ultra-broadband communication, millimeter waves will be utilized because they can transmit signals with a broader bandwidth than lower frequencies. However, since millimeter waves have a large propagation loss, a propagation distance is shorter than that of low frequencies. Therefore, in order to extend the propagation distance, it is necessary to increase an equivalent isotropic radiated power by beamforming with phased array antenna. In this paper, a phased antenna array module in combined with analog radio over fiber (A-RoF) technology for 40-GHz millimeter wave is developed and evaluated for the first time. An 8×8 phased array antenna for 40-GHz millimeter wave with integrated photodiodes and RF chains has been developed, and end-to-end transmission experiment including 20km A-RoF transmission and 3-m over-the-air transmission from the developed phased array antenna has been conducted. The results showed that the 40-GHz RF signal after the end-to-end transmission satisfied the criteria of 3GPP signal quality requirements within ±50 degrees of main beam direction.

In this paper, millimeter wave (mmWave) filtenna arrays for 5G applications are proposed. Two kinds of 2-element subarrays are designed for horizontal and vertical polarizations. Each subarray consists of three substrate integrated waveguide (SIW) cavities and two sets of stacked patches. Fully-shielded combined eighth-mode SIW (FSD-CEMSIW) cavities are used in the filtenna design. This cavity not only works as the first-stage resonator but also as the power divider for the subarray. As a result, a four-order bandpass filtering response is achieved. Filtenna arrays were fabricated and measured for demonstration. The impedance bandwidths of these subarrays cover 24-30GHz, including the 5G mmWave bands (n257, n258, and n261) with measured average gains of 8.2dBi and more than 22dB out-of-band suppression. The proposed antennas can be good candidates for 5G mmWave communication to reduce the system complexity and potential cost of the mmWave front-ends.

High-altitude platform stations (HAPSs) are recognized as a promising technology for coverage extension in the sixth generation (6G) mobile communications and beyond. The purpose of this study is to develop a HAPS system with a coverage radius of 100km and high capacity by focusing on the following two aspects: array antenna structure and user selection. HAPS systems must jointly use massive multiple-input multiple-output (mMIMO) and multiuser MIMO techniques to increase their capacity. However, the coverage achieved by a conventional planar array antenna is limited to a circular area with a radius of only tens of kilometers. A conventional semi-orthogonal user selection (SUS) scheme based on the orthogonality of channel vectors achieves high capacity, but it has high complexity. First, this paper proposes a cylindrical mMIMO system to achieve an ultra-wide coverage radius of 100km and high capacity. Second, this paper presents a novel angle-based user selection (AUS) scheme, where a user selection problem is formulated as a maximization of the minimum angular difference between users over all user groups. Finally, a low-complexity suboptimal algorithm (SA) for AUS is also proposed. Assuming an area with a 100km radius, simulation results demonstrate that the proposed cylindrical mMIMO system improves the signal-to-interference-plus-noise ratio by approx. 12dB at the boundary of the area, and it achieves approx. 1.5 times higher capacity than the conventional mMIMO which uses a planar array antenna. In addition, the results show that the proposed AUS scheme improves the lower percentiles in the system capacity distribution compared with SUS and basic random user selection. Furthermore, the computational complexity of the proposed SA is in the order of only 1/4000 that of SUS.

We present a novel circularly polarized ring microstrip antenna and its design. The shorting pins discretely disposed on the inner edge of the ring microstrip antenna are introduced as a new degree of freedom for improving the resonance frequency control. The number and diameter of the shorting pins control the resonance frequency; the resonance frequency can be almost constant with respect to the inner/outer diameter ratio, which expands the use of the ring microstrip antenna. The dual-band antenna where the proposed antenna includes another ring microstrip antenna is designed and measured, and simulated results agree well with the measured one.

This study aims to propose a novel traveling-wave series-fed microstrip array antenna and its design. The proposed antenna has two features: additional slits placed on the output side of the antenna element are introduced as a new degree of freedom to control the radiation power from each element. Also, the unequal element spacing is applied to compensate passing phases of each antenna element; meander lines that would increase the insertion loss are not used. A 9-element linear array is designed and tested, and the simulated and measured results agree, thus validating the proposed design.

We have proposed a waveguide to microstrip line transition, which perpendicularly connects one waveguide into two microstrip lines. It consists of only a waveguide and a dielectric substrate with copper foils. A backshort waveguide for typical transitions is not needed. Additionally, the transition does not require via holes on the substrate. These innovations simplify the structure and the manufacturing process. We assume that our transition and antennas are co-located on the substrate. We reduced the undesirable radiation from the transition so as not to contaminate the desirable radiation pattern. In this paper, we address output phase of our transition. Since the transition has two MSL output ports connecting to different radiation elements, the phase error between two dividing signals leads to beam shift in the radiation pattern. Unfortunately, misalignment of etching pattern between copper layers of the substrate is unavoidable. The structural asymmetry causes the phase error. In order to tolerate the misalignment, we propose to add a pair of open stubs to the transition. We show that the structure drastically stabilizes the output phase. Though the stubs create some extra radiation, we confirm that the impact is not significant. Moreover, we fabricate and measure a prototype antenna that uses the transition. In the case of with stubs, the radiation pattern is unchanged even if the misalignment is severe.

Intersymbol interference (ISI) is a significant source of degradation in many digital communication systems including our proposed non-far region communication system using large array antennas in the millimeter-wave band in which the main cause of ISI can be attributed to the path delay differences among the elements of an array antenna. This paper proposes a quantitative method to evaluate the ISI estimated from the measured near-field distribution of the array antenna. The influence of the uniformity in the aperture field distribution in ISI is discussed and compared with an ideally uniform excitation. The reliability of the proposed method is verified through a comparison with another method based on direct measurements of the transmission between the actual antennas. Finally, the signal to noise plus interference is evaluated based on the estimated ISI results and ISI is shown to be the dominant cause of the degradation in the reception zone of the system.

This paper presents a weighted spatial filter (WSF) design method based on direction of arrival (DOA) estimates for a novel array configuration called a sum and difference composite co-array. A sum and difference composite co-array is basically a combination of sum and difference co-arrays. Our configuration can realize higher degrees of freedom (DOF) with the sum co-array part at a calculation cost lower than those of the other sparse arrays. To further enhance the robustness of our proposed sum and difference composite co-array we design an optimal beam pattern by WSF based on the information of estimated DOAs. Performance of the proposed system and the DOA estimation accuracy of close-impinging waves are evaluated through computer simulations.

We propose waveguide to microstrip line transitions for automotive millimeter wave radar modules. The transitions perpendicularly connect one waveguide and one or two microstrip lines. The configuration is simple because it consists of a waveguide and a dielectric substrate with copper foils. Additionally the transitions do not need via holes on the substrate. It leads to lower costs and improved reliability. We have already proposed a via-less transition by using multi-stage impedance transformers. The impedance transformers are used for suppressing undesirable radiation from the transition as well as impedance matching. In this paper, we propose a new transition with the microstrip lines on the long axis of the waveguide while most transitions place the microstrip lines on the minor axis (electric field direction) of the waveguide. Though our transition uses bend structures of microstrip lines, which basically cause radiation, our optimized configuration can keep small radiation. We also design a transition with a single microstrip line. The proposed transition with 2 microstrip lines can be modified to the 1 microstrip line version with minimum radiation loss. Electromagnetic simulations confirm the small radiation levels expected. Additionally we fabricate the transitions with back to back structure and determine the transmission and radiation performance. We also fabricates the transition for a patch array antenna. We confirm that the undesirable radiation from the proposed transition is small and the radiation pattern of the array antenna is not worsen by the transition.

The authors have proposed a new type of flexible and printable 12GHz-band phase shifter using polymer actuator for the first time. Polymer bending actuator was used as a termination device of a reflection-type 3-dB, 90° hybrid coupler as the phase-shift control unit which controls the electrical length of the waveguide for microwave signals by the applied bias voltage. The microstrip line circuit of the device has been fabricated using low-cost screen printing method. Polymer bending actuator having three-layer stacking structure, in which an ionic liquid electrolyte layer is sandwiched with two conductive network composite layers, was formed by wet processes. The authors have confirmed that the phase shift could be controlled in analog by low driving voltages of 2-7 V for the actuator with a insertion loss of 2.73 dB. This phase shifter can be integrated with flexible patch antenna and the current flexible polymer electronics devices such as transistors.

We target the estimation of antenna patterns of distributed array antenna (DAA) systems for satellite communications. Measuring DAA patterns is very difficult because of the large antenna separations involved, more than several tens of wavelengths. Our goal is to elucidate the accuracy of the DAA pattern estimation method whose inputs are actual antenna pattern data and array factors by evaluating their similarity to actually measured DAA radiation patterns. Experiments on two Ku band parabolic antennas show that their patterns can be accurately estimated even if we change the conditions such as frequency, antenna arrangement and polarization. Evaluations reveal that the method has high estimation accuracy since its errors are better than 1dB. We conclude the method is useful for the accurate estimation of DAA patterns.

In this paper, a new array geometry is proposed which is capable of performing underdetermined Direction-Of-Arrival (DOA) estimation for the circular array configuration. DOA estimation is a classical problem and one of the most important techniques in array signal processing as it has applications in wireless and mobile communications, acoustics, and seismic sensing. We consider the problem of estimating DOAs in the case when we have more sources than the number of physical sensors where the resolution must be maintained. The proposed array geometry called Nested Sparse Circular Array (NSCA) is an extension of the two level nested linear array obtained by nesting two sub-circular arrays and one element is placed at the origin. In order to extend the array aperture, a Khatri-Rao (KR) approach is applied to the proposed NSCA which yields the virtual array structure. To utilize the increase in the degrees of freedom (DOFs) that this new array provides, a subspace based approach (MUSIC) for DOA estimation and l1-based optimization approach is extended to estimate DOAs using NSCA. Simulations show that better performance for underdetermined DOA estimation is achieved using the proposed array geometry.

A new Waffle-iron Ridge Guide (WRG) structure that has the ability to control both wavelength and impedance is proposed. With the proposed structure, not only can the wavelength be controlled over a wide range for both fast- and slow-waves in free space but the impedance can also be controlled. These features can improve the performance of array antennas in terms of reducing grating lobes and side lobes. In this paper, we discuss and evaluate a design scheme using equivalent circuits and EM-simulation. This paper also discusses how the conductivity and dielectric loss in the WRG affect the total gain of the array antenna.

This paper presents an extremely low-profile front-end configuration for a base station at quasi-millimeter wave band. It consists of integrated modules of patch antennas and substrate integrated waveguide filters using two printed circuit boards, and transmitter modules using compact GaAs pHEMT three-dimensional monolithic millimeter-wave integrated circuits. The transmitter modules are located around the integrated modules. This is because the proposed front-end configuration can attain extremely low profile, and band-pass filtering performance at quasi-millimeter wave band. As a demonstration of the proposed configuration, 26-GHz-band 4-by-4 elements front-end module is fabricated and tested. The fabricated module has the thickness of about 1 cm, while that offers the attenuation of more than 30 dB with 2 GHz offset from 26 GHz. The proposed configuration can provide base station that can be effective in offering sub-millimeter wave and millimeter-wave bands broadband services for 5G mobile communications systems.

In order to meet various requirements for the 5th generation mobile communication, a high SHF wideband massive-MIMO system has been widely studied which offers wide system bandwidth and high spectral efficiency. A hybrid beamforming configuration which combines analog beamforming by APAA (Active Phased Array Antenna) and digital MIMO signal processing is one of the promising approaches for reducing the complexity and power consumption of the high SHF wideband massive-MIMO system. In order to realize the hybrid beamforming configuration in high SHF band, small size, low power consumption and precise beam forming over the wide-band frequency range are strongly required for RF frontend which constitutes analog beam former. In this paper, a compact RF frontend module for high SHF wideband 5G small cell base station is proposed. This RF frontend module is prototyped. Various key components of the RF frontend module are fabricated in 15GHz band, and measured results show that high RF performances are able to meet the requirements of RF frontend.

A 15GHz-band 4-channel transmit/receive RF core-chip is presented for high SHF wide-band massive MIMO in 5G. In order to realize small RF frontend for 5G base stations, both 6bit phase shifters (PS) and 0.25 dB resolution variable gain amplifiers (VGA) are integrated in TX and RX paths of 4-channels on the chip. A PS calibration technique is applied to compensate the error of 6bit PS caused by process variations. A common gate current steering topology with tail current control is used for VGA to enhance the gain control accuracy. The 15GHz-band RF core-chip fabricated in 65 nm CMOS process achieved phase control error of 1.9deg. rms., and amplitude control error of 0.23 dB. rms.

This paper introduces distributed array antenna (DAA) systems that offer high antenna gain. A DAA consists of several small antennas with improved antenna gain. This paper proposes a technique that suppresses the off-axis undesired radiation and compensates the time delay by combining signal processing with optimization of array element positioning. It suppresses the undesired radiation by compensating the delay timing with high accuracy and deliberately generating the inter-symbol interference (ISI) in side-lobe directions. Computer simulations show its effective suppression of the equivalent isotropic radiated power (EIRP) pattern and its excellent BER performance.

We proposed a new architecture of antenna, transmitter and receiver feeding configuration for small synthetic aperture radar (SAR) that is compatible with 100kg class satellite. Promising applications are constellations of earth observations together with optical sensors, and responsive, disaster monitoring missions. The SAR antenna is a deployable, passive, honeycomb panel antenna with slot array that can be stowed compactly. RF (radio frequency) instruments are in a satellite body and RF signal is fed to a deployable antenna through non-contacting choke flanges at deployable hinges. This paper describes its development strategy and the present development status of the small spaceborne SAR based on this architecture.