A sub-Terahertz band is envisioned to play a great role in 6G to achieve extreme high data-rate communication. In addition to very wide band transmission, we need spatial multiplexing using a hybrid MIMO system. A recently presented paper, however, reveals that the number of observed multipath components in a sub-Terahertz band is very few in indoor environments. A channel with few multipath components is called sparse. The number of layers (streams), i.e. multiplexing gain in a MIMO system does not exceed the number of multipaths. The sparsity may restrict the spatial multiplexing gain of sub-Terahertz systems, and the poor multiplexing gain may limit the data rate of communication systems. This paper describes fundamental considerations on sub-Terahertz MIMO spatial multiplexing in indoor environments. We examined how we should steer analog beams to multipath components to achieve higher channel capacity. Furthermore, for different beam allocation schemes, we investigated eigenvalue distributions of a channel Gram matrix, power allocation to each layer, and correlations between analog beams. Through simulation results, we have revealed that the analog beams should be steered to all the multipath components to lower correlations and to achieve higher channel capacity.

In this study, product of two independent and non-identically distributed (i.n.i.d.) random variables (RVs) for κ-µ fading distribution and α-µ fading distribution is considered. The statistics of the product of RVs has been broadly applied in a large number of communications fields, such as cascaded fading channels, multiple input multiple output (MIMO) systems, radar communications and cognitive radios (CR). Exact close-form expressions of probability density function (PDF) and cumulative distribution function (CDF) with exact series formulas for the product of two i.n.i.d. fading distributions κ-µ and α-µ are deduced more accurately to represent the provided product expressions and generalized composite multipath shadowing models. Furthermore, ergodic channel capacity (ECC) is obtained to measure maximum fading channel capacity. At last, interestingly unlike κ-µ, η-µ, α-µ in [9], [17], [18], these analytical results are validated with Monte Carlo simulations and it shows that for provided κ-µ/α-µ model, non-linear parameter has more important influence than multipath component in PDF and CDF, and when the ratio between the total power of the dominant components and the total power of the scattered waves is same, higher α can significantly improve channel capacity over composite fading channels.

Channel capacity is a useful numerical index not only for grasping the upper limit of the transmission bit rate but also for comparing the abilities of various digital transmission schemes commonly used in radio-wave propagation environments because the channel capacity does not depend on specific communication methods such as modulation/demodulation schemes or error correction schemes. In this paper, modeling of the noncoherent capacity in a highly underspread WSSUS channel is investigated using a new approach. Unlike the conventional method, namely, the information theoretic method, a very straightforward formula can be obtained in a statistical manner. Although the modeling in the present study is carried out using a somewhat less rigorous approach, the result obtained is useful for roughly understanding the channel capacity in doubly selective fading environments. We clarify that the radio wave propagation parameter of the spread factor, which is the product of the Doppler spread and the delay spread, can be related quantitatively to the effective maximum signal-to-interference ratio by a simple formula. Using this model, the physical limit of wireless digital transmission is discussed from a radio wave propagation perspective.

A novel compact multi-input multi-output (MIMO) antenna system with split-ring resonator (SRR), a popular metamaterial structure, is presented. The MIMO antenna system consists of SRRs as radiator elements arranged close to each other on a printed circuit board. We evaluate the antenna characteristics with a single and two SRR elements arranged within various sizes of area. We also analyze MIMO channel capacities of SRR elements by using radiation patterns. The obtained results confirm that the proposed MIMO antenna system can achieve the same channel capacity as a conventional MIMO antenna system but with a 30% smaller footprint area and is very suitable for compact wireless equipment in next-generation wireless systems.

A simple but efficient method for evaluating the channel capacity of 2×2 multiple-input multiple-output (MIMO) antenna systems is proposed. First, the channel capacity of a half-wavelength dipole array antenna is calculated using the Monte Carlo method by changing the incident-wave signal-to-noise power ratio, the power difference between two elements, and the correlation coefficient. Using the calculated results, a polynomial function is derived by multivariate regression analysis to estimate the channel capacity. The validity of the developed function is confirmed by comparing the channel capacity estimated by the developed function with that calculated by the Monte Carlo method using a MIMO array antenna operated under various scenarios, including antenna-human body electromagnetic interactions and radio-wave propagation environments, for future MIMO systems. The function is also validated by means of two experimental approaches: the use of radiation patterns measured in an anechoic chamber and the use of a spatial fading emulator that can create a two-dimensional fading environment.

In this paper, we propose and analyze the opportunistic amplify-and-forward (AF) relaying scheme using antenna selection in conjunction with different adaptive transmission techniques over Rayleigh fading channels. In this scheme, the best antenna of a source and the best relay are selected for communication between the source and destination. Closed-form expressions for the outage probability and average symbol error rate (SER) are derived to confirm that increasing the number of antennas is the best option as compared with increasing the number of relays. We also obtain closed-form expressions for the average channel capacity under three different adaptive transmission techniques: 1) optimal power and rate adaptation; 2) constant power with optimal rate adaptation; and 3) channel inversion with a fixed rate. The channel capacity performance of the considered adaptive transmission techniques is evaluated and compared with a different number of relays and various antennas configurations for each adaptive technique. Our derived analytical results are verified through extensive Monte Carlo simulations.

A method for increasing alignment tolerance in simple multiple-stream transmission is described. Its use of π-shifted antenna directivity phase enables it to cancel interference even when antenna placement deviations occur. The interference cancellation by using π-shifted directivities provides higher alignment tolerance than that with conventional fixed weight methods. It also provides smaller channel gain variation than can be obtained using fixed weights even when antenna displacement occurs. An objective function is described that is determined by the alignment tolerance. The function is defined to maximize the alignment tolerance. The method's validity is confirmed by an experimental analysis of two-stream transmission in which the alignment tolerance of the proposed method is compared to that of conventional fixed weight methods.

In this paper, we present a weighted-polarization wearable multiple-input multiple-output (MIMO) antenna that is based on radio-frequency (RF) signal processing to realize ultra-high-speed and high-capacity mobile communications. The proposed antenna is comprised of three orthogonal dipoles, two of which can be selected according to a weight function in different usage scenarios. The weight function is determined by considering the variation in the cross-polarization power ratio (XPR) and the antenna inclination angle which depend on the radio-propagation environment and human motion. To confirm the suitability of the proposed antenna, we perform preliminary experiments to evaluate the channel capacity of a weighted-polarization wearable MIMO antenna with an arm-swinging dynamic phantom. The measured and analytical results are in good agreement, which verifies the effectiveness of the proposed antenna. We demonstrate that the proposed antenna is suitable for realizing gigabit mobile communications in future wearable MIMO applications.

Ultra-wideband (UWB) beamforming is now attracting significant research attention for attaining spatial gain from array antennas. It is commonly believed that directional antenna based communication could improve the system performance. In order to further make clear the relationship between system performance and the antenna array beamforming, UWB indoor channels are extracted from practical measurements and circular horn antenna is used to characterize the channel properties and to evaluate the system performance. Using a single beam directional antenna with a certain half power beamwidth (HPBW), the channel capacity and the bit-error-rate (BER) performance of a UWB RAKE receiver are evaluated. In the line-of-sight (LOS) environments, the channel capacity and BER performance are improved with the beamwidth becoming smaller. However in the non-line-of-sight (NLOS) environments, the capacity and BER performance are not always better with directional antennas. And the variation trend between the system performance and the antenna beamwidth disappears. This is mainly because that there exist no dominant strong path components like those seen in LOS environments. Then beam combining is introduced to further improve the system performance. Simulation results show that the channel capacity and BER performance cloud be greatly improved by multiple beam combining, especially for the NLOS environments. This reminds us that when antenna beamforming is used to obtain array gain, the beamwidth should be carefully designed and beam combining is necessary to obtain optimal performance, especially in NLOS environments.

This paper proposes a new method that combines signal modulation and FDTD (Finite-Difference Time-Domain) simulations to reduce the computation time in multiple-antenna analysis. In this method, signals are modulated so as to maintain orthogonality among the excited signals; multiple antennas are excited at the same time. This means just one FDTD simulation is needed whereas the conventional method demands as many simulations as there are transmitting antennas. The simulation of a 2×2 multi-antenna system shows that the proposed method matches the performance of the conventional method even though its computation time is much shorter.

The dramatic growth in wireless data traffic has triggered the investigation of fifth generation (5G) wireless communication systems. Small cells will play a very important role in 5G to meet the 5G requirements in spectral efficiency, energy savings, etc. In this paper, we investigate low complexity millimeter-wave communication systems with uniform circular arrays (UCAs) in line-of-sight (LOS) multiple-input multiple-output (MIMO) channels, which are used in fixed wireless access such as small cell wireless backhaul for 5G. First, we demonstrate that the MIMO channel matrices for UCAs in LOS-MIMO channels are circulant matrices. Next, we provide a detailed derivation of the unified optimal antenna placement which makes MIMO channel matrices orthogonal for 3×3 and 4×4 UCAs in LOS channels. We also derive simple analytical expressions of eigenvalues and capacity as a function of array design (link range and array diameters) for the concerned systems. Finally, based on the properties of circulant matrices, we propose a high performance low complexity LOS-MIMO precoding system that combines forward error correction (FEC) codes and spatial interleaver with the fixed IDFT precoding matrix. The proposed precoding system for UCAs does not require the channel knowledge for estimating the precoding matrix at the transmitter under the LOS condition, since the channel matrices are circulant ones for UCAs. Simulation results show that the proposed low complexity system is robust to various link ranges and can attain excellent performance in strong LOS environments and channel estimation errors.

Controlling interference from the secondary system (SS) to the receiver of the primary system (PS) is an important issue when the SS uses the same frequency band as the television broadcast system. The reason includes that the SS is unaware of the interference imposed on the primary receiver (PS-Rx), which does not have a transmitter. In this paper, we propose an interference control method between PS-Rx and SS, where a load modulation scheme is introduced to the PS-Rx. In this method, the signal from the PS transmitting station is scattered by switching its load impedance. The SS observes the scattered channel and calculates the interference suppression weights for transmitting, and controls interference by transmit beamforming. A simulation shows that the Signal-to-Interference Ratio (SIR) with interference control is improved by up to 41.5dB compared to that without interference control at short distances; the results confirm that the proposed method is effective in controlling interference between PS-Rx and SS. Furthermore, we evaluate the Signal-to-Noise Ratio (SNR) and channel capacity at SS.

This paper presents a spatial fading emulator for evaluating handset MIMO antennas in a cluster environment. The proposed emulator is based on Clarke's model and has the ability to control RF signals directly in spatial domain to generate an accurate radio propagation channel model, which includes both uniform and non-uniform angular power spectra (APS) in the horizontal plane. Characteristics of a propagation channel such as fading correlations, eigenvalues and MIMO channel capacities of handset antennas located in the vicinity of the emulator's ring can be evaluated. The measured results show that the fading emulator with 31 antenna probes is sufficient to evaluate fading correlation and MIMO channel capacity of handset antenna in the case of a narrow APS with the standard deviation of more than 20 degrees.

We theoretically study the performance of multiple-input multiple-output (MIMO) free-space optical (FSO) systems using subcarrier quadrature modulation (SC-QAM) signaling. The system average symbol-error rate (ASER) is derived taking into account the atmospheric turbulence effects on the MIMO/FSO channel, which is modeled by log-normal and the gamma-gamma distributions for weak and moderate-to-strong turbulence conditions. We quantitatively discuss the influence of index of refraction structure parameter, link distance, and different MIMO configurations on the system ASER. We also analytically derive and discuss the MIMO/FSO average (ergodic) channel capacity (ACC), which is expressed in terms of average spectral efficiency (ASE), under the impact of various channel conditions. Monte Carlo simulations are also performed to validate the mathematical analysis, and a good agreement between numerical and simulation results is confirmed.

In the literature, many resource allocation schemes have been proposed for multi-hop networks. However, the analyses provided focus mainly on the single cell case. Inter-cell interference severely degrades the performance of a wireless mobile network. Therefore, incorporating the analysis of inter-cell interference into the study of a scheme is required to more fully understand the performance of that scheme. The authors of this paper have proposed a parallel relaying scheme for a 2-hop OFDMA virtual cellular network (VCN). The purpose of this paper is to study a new version of that scheme which considers a multi-cell environment and evaluate the performance of the VCN. The ergodic channel capacity and outage capacity of the VCN in the presence of inter-cell interference are evaluated, and the results are compared to those of the single hop network (SHN). Furthermore, the effect of the location and number of wireless ports in the VCN on the channel capacity of the VCN is investigated, and the degree of fairness of the VCN relative to that of the SHN is compared. Using computer simulations, it is found that in the presence of inter-cell interference, a) the VCN outperforms the SHN even in the interference dominant transmission power region (when a single cell is considered, the VCN is better than the SHN only in the noise dominant transmission power region), b) the channel capacity of the VCN remains greater than that of the SHN even if the VCN is fully loaded, c) an optimal distance ratio for the location of the wireless ports can be found in the interval 0.2∼0.4, d) increasing the number of wireless ports from 3 to 6 can increase the channel capacity of the VCN, and e) the VCN can achieve better outage capacity than the SHN.

In the next generation mobile network, the demand for high data rate transmission will require an increase in the transmission power if the current mobile cellular network architecture is used. Multihop networks are considered to be a key solution to this problem. However, a new resource allocation algorithm is also required for the new network architecture. In this paper, we propose a resource allocation scheme for a parallel relay 2-hop OFDMA virtual cellular network (VCN) which can be applied in a multiuser environment. We evaluate, by computer simulation, the ergodic channel capacity of the VCN using the proposed algorithm, and compare the results with those of the conventional single hop network (SHN). In addition, we analyze the effect of the location of the relay wireless ports on the ergodic channel capacity of the VCN. We also study the degree of fairness of the VCN, using the proposed scheme, compared with that of the SHN. For low transmission power, the simulation results show: a) the VCN can provide a better ergodic channel capacity and a better degree of fairness than the SHN, b) the distance ratio for which the ergodic channel capacity of the VCN is maximal can be found in the interval 0.20.3, c) the ergodic channel capacity of the VCN remains better than that of the SHN as the number of users increases, and d) as the distance between the relay WPs and the base station increases, the channel capacity of VCN approaches that of the SHN.

This paper clarifies the effects of metal wires placed around a Multiple-Input-Multiple-Output (MIMO) array with the goal of improving the channel capacity in near-field MIMO systems. Tests are performed on dual-dipole arrays with metal wires placed parallel to the dipoles. If the antenna elements have an appropriate half-power beamwidth (HPBW), there is a clear improvement in the channel capacity of the dual-dipole array. The metal wires are used to increase the multipath richness and the locations of the wires significantly impact the channel capacity. A significant increase in the channel capacity is observed even if only one metal wire is placed in the proper location. We verified the generality of applying a metal wire to improve the channel capacity and that the improvement in the channel capacity is approximately proportional to the number of metal wires.

The current amplify and forward (AF) model causes interference at a mobile terminal (MT) because of relay delay or noise amplification. Therefore, this paper proposes a MIMO phase control relaying system without amplification. The proposed scheme enhances both the communication quality and the channel capacity. Computer simulations indicate the effectiveness of the proposed scheme.

Two design parameters, SNR and correlation, are key factors for enhancing channel capacity in MIMO systems. Achieving high SNR and low correlation is desirable in antenna design. This paper discusses the relation between channel capacity and these two parameters, and presents simple formulas of this relation for propagation channels and antenna coupling of mobile terminals. According to these guidelines, indoor base station antennas are designed and examined using propagation measurements. We also present a suitable antenna design for mobile terminal antennas and based on a realistic propagation model, predicted the channel capacity of the antenna.

A feed-point-selective, asymmetrically fed dipole antenna has been proposed for multiple-input multiple-output (MIMO) applications. By using PIN diode switches, an asymmetrical antenna feed is realized so as to control antenna directivities. The two basic requirements for MIMO antenna radiation patterns, namely, a decrease in overlap and control in direction, have been achieved. Additionally, to enhance directivities for the antenna with PIN diodes, a reflector has been introduced. The gain toward the reflector decreased by 2 dB, while the gain in the direction of the maximum gain increased by 2 dB. The developed antenna can correspond to a variable power angular spectrum (PAS).