Three-dimensional integrated circuits (3D ICs) that employ through-silicon vias (TSVs) integrating multiple dies vertically have opened up the potential of highly improved circuit designs. However, various types of TSV defects may occur during the assembly process, especially the clustered TSV faults because of the winding level of thinned wafer, the surface roughness and cleanness of silicon dies,inducing TSV yield reduction greatly. To tackle this fault clustering problem, router-based and ring-based TSV redundancy architectures were previously proposed. However, these schemes either require too much area overhead or have limited reparability to tolerant clustered TSV faults. Furthermore, the repairing lengths of these schemes are too long to be ignored, leading to additional delay overhead, which may cause timing violation. In this paper, we propose a region-based TSV redundancy design to achieve relatively high reparability as well as low additional delay overhead. Simulation results show that for a given number of TSVs (8*8) and TSV failure rate (1%), our design achieves 11.27% and 20.79% reduction of delay overhead as compared with router-based design and ring-based scheme, respectively. In addition, the reparability of our proposed scheme is much better than ring-based design by 30.84%, while it is close to that of the router-based scheme. More importantly, the overall TSV yield of our design achieves 99.88%, which is slightly higher than that of both router-based method (99.53%) and ring-based design (99.00%).

Recently, many neural networks have been proposed for radar sea clutter suppression. However, they have poor performance under the condition of low signal to interference plus noise ratio (SINR). In this letter, we put forward a novel method to detect a small target embedded in sea clutter based on an optimal filter. The proposed method keeps the energy in the frequency cell under test (FCUT) invariant, at the same time, it minimizes other frequency signals. Finally, detect target by judging the output SINR of every frequency cell. Compared with the neural networks, the algorithm proposed can detect under lower SINR. Using real-life radar data, we show that our method can detect the target effectively when the SINR is higher than -39dB which is 23dB lower than that needed by the neural networks.

Semi-bent functions have almost maximal nonlinearity. In this paper, two classes of semi-bent functions are constructed by modifying the supports of two quadratic Boolean functions $f_1(x_1,x_2,cdots,x_n)=igopluslimits^{k}_{i=1}x_{2i-1}x_{2i}$ with $n=2k+1geq3$ and $f_2(x_1,x_2,cdots,x_n)=igopluslimits^{k}_{i=1}x_{2i-1}x_{2i}$ with $n=2k+2geq4$. Meanwhile, the algebraic normal forms of the newly constructed semi-bent functions are determined.

A minor component analysis approach based on the generalized sidelobe canceler is presented to realize the blind suppression of multiple-access interference in multicarrier code division multiple access systems. With a rough user-code and timing estimations, this proposed method of less computation performs the same as minimum mean square error detectors and outperforms existing blind detectors. Simulation results illustrate the effectiveness of the blind multiuser detection.

With the scaling of technology, nanoscale CMOS integrated circuits are becoming more sensitive to single event double node upsets induced by charge sharing. A novel highly robust hardened latch design is presented that is fully resilient to single event double node upsets and single node upsets. The proposed latch employs multiple redundant C-elements to form a dual interlocked structure in which the redundant C-elements can bring the affected nodes back to the correct states regardless of the energy of the striking particle. Detailed HSPICE results confirm that the proposed latch features complete resilience to double node upsets and achieves an improved trade-off in terms of robustness, area, delay and power in comparison with previous latches. Extensive Monte Carlo simulations validate the proposed latch features as less sensitive to process, supply voltage and temperature variations.

Reducing the energy consumption of wireless communication systems with new technologies and solutions continues to be an important concern in developing future standards. In this paper, we study the routing strategies in multi-hop relaying networks. For a 2-way assignment routing method, an efficient feedback scheme is presented to minimize the power consumption over the whole system. Compared with the full channel information in traditional feedback scheme, only the backward accumulated feedback metrics are required. If the proposed routing calculation is used, there is no performance loss. When the number of the hops and the relays is large, the new scheme achieves a significant feedback overhead reduction. Moreover, we show a proof for the optimality of the presented routing strategy based on mathematical induction.

The recently proposed distributed adaptive direct position determination (D-ADPD) algorithm provides an efficient way to locating a radio emitter using a sensor network. However, this algorithm may be suboptimal in the situation of colored emitted signals. We propose an enhanced distributed adaptive direct position determination (EDA-DPD) algorithm. Simulations validate that the proposed EDA-DPD outperforms the D-ADPD in colored emitted signals scenarios and has the similar performance with the D-ADPD in white emitted signal scenarios.

A novel NiSi technology with bi-layer Co/TiN structure as a capping layer is proposed for the highly thermal immune Ni Silicide technology. Much better thermal immunity of Ni Silicide was certified up to 700, 30 min post silicidation furnace annealing by introducing Co/TiN bi-layer capping. The proposed structure is successfully applied to nano-scale CMOSFET with a gate length of 80 nm. The sheet resistance of nano-scale gate poly shows little degradation even after the high temperature furnace annealing of 650, 30 min. The Ni/Co/TiN structure is very promising for the nano-scale MOSFET technology which needs the ultra shallow junction and high temperature post silicidation processes

Dependent Quantization (DQ) is a new quantization tool introduced in the Versatile Video Coding (VVC) standard. While it provides better rate-distortion calculation accuracy, it also increases the computational complexity and hardware cost compared to the widely used scalar quantization. To address this issue, this paper proposes a parallel-dependent quantization hardware architecture using Verilog HDL language. The architecture preprocesses the coefficients with a scalar quantizer and a high-frequency filter, and then further segments and processes the coefficients in parallel using the Viterbi algorithm. Additionally, the weight bit width of the rate-distortion calculation is reduced to decrease the quantization cycle and computational complexity. Finally, the final quantization of the TU is determined through sequential scanning and judging of the rate-distortion cost. Experimental results show that the proposed algorithm reduces the quantization cycle by an average of 56.96% compared to VVC’s reference platform VTM, with a Bjøntegaard delta bit rate (BDBR) loss of 1.03% and 1.05% under the Low-delay P and Random Access configurations, respectively. Verification on the AMD FPGA development platform demonstrates that the hardware implementation meets the quantization requirements for 1080P@60Hz video hardware encoding.

This Letter proposes a way of resolving spreading code mismatch in blind multiuser detection with subspace-based technique. It has been shown that subspace-based (SSB) blind multiuser detectors demonstrate the advantages of fast convergence speed and less sensitivity to spreading code mismatch over constrained mean output energy (CMOE) detectors. With a corrected scheme of the desired user code, the proposed method offers more robust capabilities over existing SSB techniques. Numerical results show that the effectiveness of the proposed technique.

Two simple frequency offset estimators based on projection approaches for multicarrier code-division multiple access systems are proposed, without using specific training sequences. It is not only can estimate and correct frequency offset, but also has less computational load. Several computer simulations are provided for illustrating the effectiveness of the blind estimate approaches.

Root cause analysis of BGP updates is the key to debug and troubleshoot BGP routing problems. However, it is a challenge to precisely diagnose the cause and the origin of routing instability. In this paper, we are the first to distinguish link failure events from policy change events based on BGP updates from single vantage points by analyzing the relationship of the closed loops formed through intersecting all the transient paths during instability and the length variation of the stable paths after instability. Once link failure events are recognized, their origins are precisely inferred with 100% accuracy. Through simulation, our method is effective to distinguish link failure events from link restoration events and policy related events, and reduce the size of candidate set of origins.

This paper reports a high-quality hardware-friendly integer motion estimation (IME) scheme. According to different characteristics of CTU content, the proposed method adopts different adaptive multi-resolution strategies coupled with accurate full-PU modes IME at the finest level. Besides, by using motion vector derivation, IME for the second reference frame is simplified and hardware resource is saved greatly through processing element (PE) sharing. It is shown that the proposed architecture can support the real-time processing of 4K-UHD @60fps, while the BD-rate is just increased by 0.53%.

Although the classical vector median filter (VMF) has been widely used to suppress the impulse noise in the color image, many thin color curve pixels aligned in arbitrary directions are usually removed out as impulse noise. This serious problem can be solved by the proposed method that can protect the thin curves in arbitrary direction in color image and remove out the impulse noise at the same time. Firstly, samples in the 3x3 filter window are considered to preliminarily detect whether the center pixel is corrupted by impulse noise or not. Then, samples outside a 5x5 filter window are conditionally and partly considered to accurately distinguish the impulse noise and the noise-free pixel. At last, based on the previous outputs, samples on the processed positions in a 3x3 filter window are chosen as the samples of VMF operation to suppress the impulse noise. Extensive experimental results indicate that the proposed algorithm can be used to remove the impulse noise of color image while protecting the thin curves in arbitrary directions.

As a next-generation CAN (Controller Area Network), CAN FD (CAN with flexible data rate) has attracted much attention recently. However, how to use the improved bus bandwidth efficiently in CAN FD is still an issue. Contrasting with existing methods using greedy approximate algorithms, this paper proposes a genetic algorithm for CAN FD frame packing. It tries to minimize the bandwidth utilization by considering the different periods of signals when packing them in the same frame. Moreover, it also checks the schedulability of packed frames to guarantee the real-time constraints of each frame and proposed a merging algorithm to improve the schedulability for signal set with high bus load. Experimental results validate that the proposed algorithm can achieve significantly less bandwidth utilization and improved schedulability than existing methods for a given set of signals.

A Decision Feedback Equalizer (DFE) structure with a varying number of tap lengths was used with a recursive least squares (RLS) algorithm to determine tradeoffs between equalizer size and performance in mobile and portable digital radio systems. A mobile channel simulator, SMRCIM, was used to demonstrate how much an equalizer can improve the BER in real world urban channels. The results show that at 850MHz, the DFE is unable to improve the BER when the mobile terminal exceeds speeds of 115km/h for U.S. Digital Cellular systems. The performance of adaptive equalization for indoor high data rate systems was evaluated using the indoor channel simulator SIRCIM, and we found that DFEs have excellent performance for indoor radio channels. For simple structures, the BER is less than 10-3 at 15dB Eb/NO using coherent QPSK modulation. Finally, an equalizer structure for non-coherent π/4 DQPSK modulation was developed and simulation results are presented.

Last year, a new notion of rep-cube was proposed. A rep-cube is a polyomino that is a net of a cube, and it can be divided into some polyominoes such that each of them can be folded into a cube. This notion was inspired by the notions of polyomino and rep-tile, which were introduced by Solomon W. Golomb. It was proved that there are infinitely many distinct rep-cubes. In this paper, we investigate this new notion and show further results.

In this letter, we present a normalized least-mean-square algorithm of blind estimator for carrier frequency offset estimation of orthogonal frequency division multiplexing systems. In conjunction with the closed-loop estimate structure, the proposed efficient algorithm eliminates the inter-carrier interference for time varying carrier frequency offset. The proposed algorithm offers faster convergence speed and more accuracy to the carrier frequency offset estimate. Several computer simulation examples are presented for illustrating and effectiveness of the proposed algorithm.

To help student nurses learn to transfer patients from a bed to a wheelchair, this paper proposes a system for automatic skill evaluation in nurses' training for this task. Multiple Kinect sensors were employed, in conjunction with colored markers attached to the trainee's and patient's clothing and to the wheelchair, in order to measure both participants' postures as they interacted closely during the transfer and to assess the correctness of the trainee's movements and use of equipment. The measurement method involved identifying body joints, and features of the wheelchair, via the colors of the attached markers and calculating their 3D positions by combining color and depth data from two sensors. We first developed an automatic segmentation method to convert a continuous recording of the patient transfer process into discrete steps, by extracting from the raw sensor data the defining features of the movements of both participants during each stage of the transfer. Next, a checklist of 20 evaluation items was defined in order to evaluate the trainee nurses' skills in performing the patient transfer. The items were divided into two types, and two corresponding methods were proposed for classifying trainee performance as correct or incorrect. One method was based on whether the participants' relevant body parts were positioned in a predefined spatial range that was considered ‘correct’ in terms of safety and efficacy (e.g., feet placed appropriately for balance). The second method was based on quantitative indexes and thresholds for parameters describing the participants' postures and movements, as determined by a Bayesian minimum-error method. A prototype system was constructed and experiments were performed to assess the proposed approach. The evaluation of nurses' patient transfer skills was performed successfully and automatically. The automatic evaluation results were compared with evaluation by human teachers and achieved an accuracy exceeding 80%.

A highly parallel turbo decoder for 3GPP LTE/LTE-Advanced systems is presented. It consists of 32 radix-4 soft-in/soft-out (SISO) decoders. Each SISO decoder is based on the proposed full-parallel sliding window (SW) schedule. Implemented in a 0.13 µm CMOS technology, the proposed design occupies 12.96 mm2 and achieves 1.5 Gb/s while decoding size-6144 blocks with 5.5 iterations. Compared with conventional SW schedule, the throughput is improved by 30–76% with 19.2% area overhead and negligible energy overhead.