In this study, we investigate outdoor propagation measurements performed in an industrial park environment at 28.3GHz band. The propagation characteristics were evaluated with the measurement result regarding the path loss characteristics. Ray tracing simulation was also studied and compared with the measurement data to evaluate the quantitative accuracy of ray tracing in millimeter-wave band wireless propagations. Ray tracing, whose accuracy was evaluated based on a comparison with the measurement results, can aid in the theoretical design of the coverage area and deterministic channel modeling.

Basic characteristics for relating design and base station layout design in land mobile communications are provided through a propagation model for path loss prediction. Owing to the rapid annual increase in traffic data, the number of base stations has increased accordingly. Therefore, propagation models for various scenarios and frequency bands are necessitated. To solve problems optimization and creation methods using the propagation model, a path loss prediction method that merges multiple models in machine learning is proposed herein. The method is discussed based on measurement values from Kitakyushu-shi. In machine learning, the selection of input parameters and suppression of overlearning are important for achieving highly accurate predictions. Therefore, the acquisition of conventional models based on the propagation environment and the use of input parameters of high importance are proposed. The prediction accuracy for Kitakyushu-shi using the proposed method indicates a root mean square error (RMSE) of 3.68dB. In addition, predictions are performed in Narashino-shi to confirm the effectiveness of the method in other urban scenarios. Results confirm the effectiveness of the proposed method for the urban scenario in Narashino-shi, and an RMSE of 4.39dB is obtained for the accuracy.

Expectation propagation (EP) is a powerful algorithm for signal recovery in compressed sensing. This letter proposes correction of a variance message before denoising to improve the performance of EP in the high signal-to-noise ratio (SNR) regime for finite-sized systems. The variance massage is replaced by an observation-dependent consistent estimator of the mean-square error in estimation before denoising. Massive multiple-input multiple-output (MIMO) is considered to verify the effectiveness of the proposed correction. Numerical simulations show that the proposed variance correction improves the high SNR performance of EP for massive MIMO with a few hundred transmit and receive antennas.

This paper proposes a measurement-based spectrum database (MSD) with clustered fading distributions toward greater storage efficiencies. The conventional MSD can accurately model the actual characteristics of multipath fading by plotting the histogram of instantaneous measurement data for each space-separated mesh and utilizing it in communication designs. However, if the database contains all of a distribution for each location, the amount of data stored will be extremely large. Because the main purpose of the MSD is to improve spectral efficiency, it is necessary to reduce the amount of data stored while maintaining quality. The proposed method reduces the amount of stored data by estimating the distribution of the instantaneous received signal power at each point and integrating similar distributions through clustering. Numerical results show that clustering techniques can reduce the amount of data while maintaining the accuracy of the MSD. We then apply the proposed method to the outage probability prediction for the instantaneous received signal power. It is revealed that the prediction accuracy is maintained even when the amount of data is reduced.

To achieve highly efficient spectrum usage, dynamic sharing of scarce spectrum resources has recently become the subject of intense discussion. The technologies of dynamic spectrum sharing (DSS) have already been adopted or are scheduled to be adopted in a number of countries, and Japan is no exception. The authors and organizations collaborating in the research and development project being undertaken in Japan have studied a novel DSS system positioned between the fifth-generation mobile communication system (5G system) and different incumbent radio systems. Our DSS system has three characteristics. (1) It detects dynamically unused sharable spectrums (USSs) of incumbent radio systems for the space axis by using novel propagation models and estimation of the transmitting location with radio sensor information. (2) It manages USSs for the time axis by interference calculation with propagation parameters, fair assignment and future usage of USSs. (3) It utilizes USSs for the spectrum axis by using methods that decrease interference for lower separation distances. In this paper, we present an overview and the technologies of our DSS system and its applications in Japan.

Optical code-division multiple-access (CDMA) techniques provide multi-user data transmission services in optical wireless and fiber communication systems. Several signature codes, such as modified prime sequence codes (MPSCs), generalized MPSCs (GMPSCs) and modified pseudo-orthogonal M-sequence sets, have been proposed for synchronous optical CDMA systems. In this paper, a new scheme is proposed for synchronous optical CDMA to increase the number of users and, consequently, to increase the total data rate without increasing the chip rate. The proposed scheme employs a GMPSC and an extended bi-orthogonal code which is a unipolar code generated from a bipolar Walsh code. Comprehensive comparisons between the proposed scheme and several conventional schemes are shown. Moreover, bit error rate performance and energy efficiency of the proposed scheme are evaluated comparing with those of the conventional optical CDMA schemes under atmospheric propagation environment.

Path loss in high frequency bands above 6GHz is the most fundamental and significant propagation characteristic of IMT-2020. To develop and evaluate such high frequency bands, ITU-R SG5 WP5D recently released channel models applicable up to 100GHz. The channel models include path loss models applicable to 0.5-100GHz. A path loss model is used for cell design and the evaluation of the radio technologies, which is the main purpose of WP5D. Prediction accuracy in various locations, Tx positions, frequency bands, and other parameters are significant in cell design. This article presents the prediction accuracy of UMa path loss models which are detailed in Report ITU-R M.2412 for IMT-2020. We also propose UMa_A' as an extension model of UMa_A. While UMa_A applies different equations to the bands below and above 6GHz to predict path loss, UMa_A' covers all bands by using the equations of UMa_A below 6GHz. By using the UMa_A' model, we can predict path loss by taking various parameters (such as BS antenna height) into account over a wide frequency range (0.5-100GHz). This is useful for considering the deployment of BS antennas at various positions with a wide frequency band. We verify model accuracy by extensive measurements in the frequency bands from 2 to 66GHz, distances up to 1600 m, and an UMa environment with three Tx antenna heights. The UMa_A' extension model can predict path loss with the low RMSE of about 7dB at 2-26.4GHz, which is more accurate than the UMa_A and UMa_B models. Although the applicability of the UMa_A' model at 66GHz is unclear and needs further verification, the evaluation results for 66GHz demonstrate that the antenna height may affect the prediction accuracy at 66GHz.

This paper addresses pilot contamination in massive multiple-input multiple-output (MIMO) uplink. Pilot contamination is caused by reuse of identical pilot sequences in adjacent cells. To solve pilot contamination, the base station utilizes differences between the transmission frames of different users, which are detected via joint channel and data estimation. The joint estimation is regarded as a bilinear inference problem in compressed sensing. Expectation propagation (EP) is used to propose an iterative channel and data estimation algorithm. Initial channel estimates are attained via time-shifted pilots without exploiting information about large scale fading. The proposed EP modifies two points in conventional bilinear adaptive vector approximate message-passing (BAd-VAMP). One is that EP utilizes data estimates after soft decision in the channel estimation while BAd-VAMP uses them before soft decision. The other point is that EP can utilize the prior distribution of the channel matrix while BAd-VAMP cannot in principle. Numerical simulations show that EP converges much faster than BAd-VAMP in spatially correlated MIMO, in which approximate message-passing fails to converge toward the same fixed-point as EP and BAd-VAMP.

Sparse orthogonal matrices are proposed to improve the convergence property of expectation propagation (EP) for sparse signal recovery from compressed linear measurements subject to known dense and ill-conditioned multiplicative noise. As a typical problem, this letter addresses generalized spatial modulation (GSM) in over-loaded and spatially correlated multiple-input multiple-output (MIMO) systems. The proposed sparse orthogonal matrices are used in precoding and constructed efficiently via a generalization of the fast Walsh-Hadamard transform. Numerical simulations show that the proposed sparse orthogonal precoding improves the convergence property of EP in over-loaded GSM MIMO systems with known spatially correlated channel matrices.

This paper presents a 120-GHz-band split ring resonator (SRR) bandstop filter whose insertion loss can be controlled by coupling another lattice pattern substrate. The SRR bandstop filter and lattice pattern substrate is composed of 200-µm-thick quartz substrate and 5-µm-thick gold patterns. S21 of the SRR bandstop filter is -37.8 dB, and its -10-dB bandwidth is 115-130 GHz. S21 of the SRR bandstop filter changes to -4.1 dB at 125 GHz by arranging the lattice pattern substrate in close proximity to the SRR stopband filter, because coupling between the SRR and the lattice pattern occurs when the SRR and lattice pattern are opposed in close proximity. It was found that 10 Gbit/s data transmission can be achieved by setting the lattice pattern substrate just above the SRR bandstop filter with a spacer thickness of 50 µm, even though data transmission is impossible when only the SRR bandstop filter is inserted between the transmitter and the receiver.

Diffusion least-mean-square (LMS) is a method to estimate and track an unknown parameter at multiple nodes in a network. When the unknown vector has sparsity, the sparse promoting version of diffusion LMS, which utilizes a sparse regularization term in the cost function, is known to show better convergence performance than that of the original diffusion LMS. This paper proposes a novel choice of the coefficients involved in the updates of sparse diffusion LMS using the idea of message propagation. Moreover, we optimize the proposed coefficients with respect to mean-square-deviation at the steady-state. Simulation results demonstrate that the proposed method outperforms conventional methods in terms of the convergence performance.

Expectation propagation (EP) decoding is proposed for sparse superposition coding in orthogonal frequency division multiplexing (OFDM) systems. When a randomized discrete Fourier transform (DFT) dictionary matrix is used, the EP decoding has the same complexity as approximate message-passing (AMP) decoding, which is a low-complexity and powerful decoding algorithm for the additive white Gaussian noise (AWGN) channel. Numerical simulations show that the EP decoding achieves comparable performance to AMP decoding for the AWGN channel. For OFDM systems, on the other hand, the EP decoding is much superior to the AMP decoding while the AMP decoding has an error-floor in high signal-to-noise ratio regime.

This paper presents non-destructive millimeter-wave (MMW) imaging of sub-millimeter-wide cracks on a concrete surface covered with paper. We measured the near-field scattering of 76.5 GHz-MMW signals at concrete surface cracks for detection of the sub-millimeter-wide cracks. A decrease in the received signal magnitude by near-field scattering at the fine concrete surface crack was slight, which yielded an unclear MMW image contrast of fine cracks at the concrete surface. We have found that the received signal magnitude at concrete surface crack is larger than that at the surface without a crack, when the paper thickness is almost equal to n/4 of the effective wavelength of the MMW signal in the paper (n=1, 3, 5 ...), thus, making MMW image contrast at the surface crack reversed. By calculating the difference of two MMW images obtained from different paper thickness, we were able to improve the MMW image contrast at the surface crack by up to 3.3 dB.

When considering the deployment of a radio communications network, the study of multipath interference and its impact on the quality of signal reception is of the outmost importance in order to meet the necessary performance requirements. This work considers specifically the case of the lunar surface as the mission scenario for a community of autonomous mobile exploration robots, which communicate through a radiofrequency network to accomplish their mission. In this application, the low height of the mobile robots makes the influence of multipath interference effects on the performance of the radio communication channel relevant. However, no specific information about lunar soil reflection coefficients characteristics is available for radiofrequency communication bands. This work reviews the literature on the electrical parameter of Lunar soil. From this base, the reflection coefficients are estimated for the assumed radio profile in different communications frequency bands. Finally, the results obtained are discussed.

This paper analyzes the effect of error propagation of decision feedback equalizer (DFE) for PAM4 based 400Gb/s Ethernet. First, an analytic model for the error propagation is proposed to estimate the probability of different burst error length due to error propagation for PAM4 link system with multi-tap TX FFE (Feed Forward Equalizer) + RX DFE architecture. After calculating the symbol error rate (SER) and bit error rate (BER) based on the probability model, the theoretical analysis about the impact of different equalizer configurations on BER is compared with the simulation results, and then BER performance with FEC (Forward Error Correction) is analyzed to evaluate the effect of DFE error propagation on PAM4 link. Finally, two FEC interleaving schemes, symbol and bit interleaving, are employed in order to reduce BER further and then the theoretical analysis and the simulation result of their performance improvement are also evaluated. Simulation results show that at most 0.52dB interleaving gain can be achieved compared with non-interleaving scheme just at a little cost in storing memory and latency. And between the two interleaving methods, symbol interleaving performs better compared with the other one from the view of tradeoff between the interleaving gain and the cost and can be applied for 400Gb/s Ethernet.

Interference alignment (IA) in temporal domain is important in the case of single-antenna vehicle communications. In this paper, perfect cyclic IA based on propagation delay is extended to the K×2 X channels with two receivers and arbitrary transmitters K≥2, which achieves the maximal multiplexing gain by obtaining the theoretical degree of freedom of 2K/(K+1). We deduce the alignment and separability conditions, and propose a general scheme which is flexible in setting the index of time-slot for IA at the receiver side. Furthermore, the feasibility of the proposed scheme in the two-/three- Euclidean space is analyzed and demonstrated.

In the beam-type microwave power transmission system, it is required to minimize the interference with communication and the influence on the human body. Retrodirective system that re-radiates a beam in the direction of arrival of a signal is well known as a beam control technique for accurate microwave power transmission. In this paper, we newly propose to apply the retrodirective system to both transmitting and receiving antennas. The leakage to the outside of the system is expected to minimize self-convergently while following the atmospheric fluctuation and the antenna movement by repeating the retrodirective between the transmitting and receiving antenna in this system. We considered this phenomenon theoretically using an infinite array antenna model. Finally, it has been shown by the equivalent circuit simulation that stable transmission can be realized by oscillating the system.

Human gender recognition in the wild is a challenging task due to complex face variations, such as poses, lighting, occlusions, etc. In this letter, learnable Gabor convolutional network (LGCN), a new neural network computing framework for gender recognition was proposed. In LGCN, a learnable Gabor filter (LGF) is introduced and combined with the convolutional neural network (CNN). Specifically, the proposed framework is constructed by replacing some first layer convolutional kernels of a standard CNN with LGFs. Here, LGFs learn intrinsic parameters by using standard back propagation method, so that the values of those parameters are no longer fixed by experience as traditional methods, but can be modified by self-learning automatically. In addition, the performance of LGCN in gender recognition is further improved by applying a proposed feature combination strategy. The experimental results demonstrate that, compared to the standard CNNs with identical network architecture, our approach achieves better performance on three challenging public datasets without introducing any sacrifice in parameter size.

Positioning information plays a significant role in multi-unmanned aerial vehicles (UAVs) applications. Traditionally, the positioning information is widely provided by Global Navigation Satellite System (GNSS) due to its good performance and global coverage. However, owing to complicated flight environment or signal blockage, jamming and unintentional interference, the UAVs may fail to locate themselves by using GNSS alone. As a new method to resolve these problems, cooperative positioning, by incorporating peer-to-peer range measurements and assisted information, has attracted more and more attentions due to its ability to enhance the accuracy and availability of positioning. However, achieving good performance of cooperative positioning of multi-UAVs is challenging as their mobility, arbitrary nonlinear state-evolution, measurement models and limited computation and communication resources. In this paper, we present a factor graph (FG) representation and message passing methodology to solve cooperative positioning problem among UAVs in 3-dimensional environment where GNSS cannot provide services. Moreover, to deal with the nonlinear state-evolution and measurement models while decreasing the computation complexity and communication cost, we develop a distributed algorithm for dynamic and hybrid UAVs by means of Spherical-Radial Cubature Rules (CR) method with belief propagation (BP) and variational message passing (VMP) methods (CRBP-VMP) on the FG. The proposed CRBP deals with the highly non-linear state-evolution models and non-Gaussian distributions, the VMP method is employed for ranging message, gets the simpler message representation and can reduce communication cost in the joint estimation problem. Simulation results demonstrate that the higher positioning accuracy, the better convergence as well as low computational complexity and communication cost of the proposed CRBP-VMP algorithm, which can be achieved compared with sum-product algorithm over a wireless network (SPAWN) and traditional Cubature Kalman Filters (CKF) method.

Forecasting commodity futures price is a challenging task. We present an algorithm to predict the trend of commodity futures price based on a type of structuring data and back propagation neural network. The random volatility of futures can be filtered out in the structuring data. Moreover, it is not restricted by the type of futures contract. Experiments show the algorithm can achieve 80% accuracy in predicting price trends.